Factory crimp dies

Lee factory crimp dies - Texas Hunting Forum

News & Announcements, Trading Post - Swap - Classifieds, non-hunting, CLASSIFIEDS, Firearms Sales, Trades and Gun... Photos & Videos, Videos, IN THE FIELD

What am I doing wrong with this Lee Factory Crimp Die?

The die isn't crimping anything. I screw the die down until it touches the shell holder, then another half turn, per the instructions. But when I run a round ...

Lee Factory Crimp Die - Is it necessary??? - Glock Talk

The short answer is, yes, a crimp is needed. But what that really means is to "crimp" just enough to remove the flair that was made by the ...

Lee FCD (factory crimp die) in 9mm, I gots questions

Justy set the die up per the instructions that come with the die. When you set it up, a half a turn (of knurled knob) for a light crimp, full ...

Difference visually between Lee Factory crimp & Lee seating die

The bullet seating die will have a "plunger" inside that mates to the bullet and, ideally, will be the same shape as the bullet tip. It pushes the bullet into ...

Why Do I Need The Lee Factory Crimp Die? - YouTube

For those reloaders who do not use the Lee Factory Crimp Dies, here is the answer to the question...

OUTDOORS: LeBlanc: Benefits of using Factory Crimp Dies

A commonly used tactic in a factory round is a crimp to help hold the bullet in place before it's launched, especially when there is a heavy ...

Lee Factory Crimp Die with .32SWL Wadcutters - TargetTalk

Try this... Size your fired cases with the Lee Factory Carbide Crimp Die. They should measure about 0.337". Prime as usual.

Lee factory crimp die | Shooters' Forum

The Lee Factory Crimp Die for pistol round is great. It makes for almost no malfunctioning problems in semi-autos for me.

Lee factory crimp die in an RCBS press - Long Range Hunting Forum

Set crimp amount by feel - screw die into press to get desired crimp. Presses have different length handles and different mechanics so what is ...

lee factory crimp die - Modern Sporting Rifle Evolution

The collet style factory crimp dies have been used by the 450 Bushmaster shooters to give the case a side crimp into the bullet shank. They ...

Lee Carbide Factory Crimp Die - Lee Loader

Re: Lee Carbide Factory Crimp Die ... I did take it apart. Correct direction. I measured each end I.D and O.D., and also checked inside of the sleeve for the ...

Lee Factory Crimp Die - Any advantage - The Firing Line Forums

This die post sizes a round to a standard diameter and taper crimps it. Some reloaders use only the sizing feature others remove the sizing ring and only crimp ...

Lee factory crimp die | Shooters Forum

Note that the standard Lee Factory Crimp Die with crimping collet cannot be made short enough for pistol rounds. The collet fingers get too ...

Lee Factory Crimp Die and cast bullets

I have the Lee Factory Crimp Die for a number of pistol and revolver calibers. I think the trick here, is to use the “tool” when it benefits you and don't when ...

Lee Factory Crimp Die | AfricaHunting.com

Lee 416 Rem factory crimp die will work on a 404 Jeffery. Sometimes the whole internal collet will come out but most times ok. If it does come out easy to put ...

Lee factory crimp die- pros and cons? | Graybeard Outdoors

IF you need to crimp at all and IF you need the features the FCDs provide then they are the better crimpers. The biggest obsticle to consistant ...

anyone using lee factory crimp die? | Sniper's Hide Forum

The Lee Factory Crimp Die is the best way to do it. A 308 Winchester round, however, doesn't need a crimp even if to be shot in an autoloader.

Lee factory crimp die – The ExhaustNotes Blog

The Lee factory crimp die is a good thing. It works. It holds bullets in place better, it improves chambering, and it improves accuracy.

Single Station Carbide Factory Crimp Die Installation - YouTube

Share your videos with friends, family, and the world.