what size wire for alternator to cutoff switch and batter in trunk

Battery disconnect switch...what gauge wire? | GM Square Body - 1973

2 gauge will be fine I do like welding cable because it is finer strands = better conducting. but any 2 gauge should be fine. You must be ...

How many feet of cable for Battery Relocation? And what Gauge?

- Also use 2ga wire to connect the alternator to the cut off switch(10 ft or so). - Don't forget to use an inline fuse there. ... - Use 10ga(2ft) ...

Wiring questions, alternator/starter - LS1TECH - Camaro and ...

I have 16 or 18 feet of 4GA cable about to go from battery, to cutoff, then from cutoff to starter. I am only going to need 8 gauge to keep ...

Technical - How to wire a battery to the trunk - The Jalopy Journal

Basically that is exactly what we do in race cars. use a diode on the Alternator wire [up near the main disconnect switch], and put the fusible ...

Charging wire to battery in trunk - V8buick.com

... wire from the alternator to the trunk battery. I have a 105 amp alternator. What gauge ... battery kill switch the car will shut off. ronbz455, ...

Battery Relocation, Remote Cutoff Switch, and Alternator Solenoid

the smaller of the 2 poles is meant for the alternator field wire. this will kill the alternator putting out voltage and the other pole cuts off the battery. I ...

Fuse size for wire from alternator to trunk mounted soleniod/battery?

What amp rating should the fuse be? The alternator is a G3, so it can potentialy put out 130amps. Also, instead of a fuse, a circuit should do ...

Battery relocation | For A Bodies Only Mopar Forum

Not a good idea. The “existing” wires are typically 4 and 6 gauge wires. To run the battery to the trunk you should be running 0 or 1 gauge.

What gauge wire to secondary battery - Ford Truck Enthusiasts Forums

I understand my alternator is 90 amp and so I should size the wire to that amp rating (4 AWG). My van came with a battery in the trunk wired ...

trunk mount, fusible link on alt. wire?? | Ford Mustang Forums

8 gauge is a little small for the run length. Alternator wire i would suggest 4 gauge. Battery 2 gauge. :worthless.

battery in trunk and kill switch question - Hot Rod Forum

If you choose to go with a firewall juntion lug you will have one wire from it going to power your fuse panel and another wire from it going to ...

Using a master disconnect switch with an alternator - YouTube

Alternator Kill Switch Proper Wiring: Tech Tip Tuesday ... Making the Battery Cutoff Switch Kill ... How to wire and use a remote battery disconnect.

Battery relocation Wires - Honda-Tech - Honda Forum Discussion

If you run it to the trunk then I'd go 2 gauge from the battery to wherever you put your post, and add some loom to it to make sure it doesn't ...

Moving the battery to the trunk - MonteCarloSS.com Message Board

For the cutoff switch to work properly you have to run your alternator wire directly back to the (+) positive terminal of your battery. Yes ...

Battery in Trunk | Team Chevelle

To size the wire or cables, you need to know what the demands are of the starter and what is the maximum the alternator can put out. You can ...

Battery Relocation to Trunk or Other Area of Your Vehicle

Using 2 gauge battery cables is the minimum for a trunk mounted battery, but using 1 gauge or 1/0 (zero gauge) wiring may be needed. What size ...

alternator wiring help | For B Bodies Only Classic Mopar Forum

Keeping the OEM black wire connected will provide a power source and defeat the cutoff switch. I'm not a fan of a hot wire to the alternator all ...

Battery in trunk? | Super Coupe Club of America

Now run at least an 8 gauge cable from the starter relay (same post that the alternator cable attaches to), all the way back to your kill switch ...

how do you wire a kill switch for drag racing? - www.ka-t.org

I ran an 8 gauge wire directly from the alternator output terminal to the positive battery terminal in the trunk. Make sure you take off the ...

Battery relocation and Wiring - Ford Mustang Forum

Are you going to run at a dragstrip? If so then you have to use a cutoff switch so you have to set it up like that gif shows. If not, you can ...