Pertronix Ignition

Pertronix electronic ignition, what wires? : The 3000 Forum

Read the Pertronix instructions carefully and you will see that you should NOT use copper core wires and the yellow/black bumblebee wires I have been using are ...

Pertronix Electronic Ignition | Japanese Mini Truck Forum

The 550-cc EB, and 660-cc EF Daihatsu engines all have Denso, counter clockwise rotation distributors. So, if you have an S81, or S83, or early ...

How to Install the Pertronix Electronic Ignition - YouTube

Check out my website for car parts and merch that I am selling - https://krusebuilt.com/ One of the easiest Mods to these classic vehicles ...

12 v ignition power source for pertronix - TheLincolnForum.Net

Quick answer: ORANGE-YELLOW STRIPE wire coming off a relay with a black connector with three wires (other two wires are BLUE and WHITE).

Pertronix Ignitor: reliability & suitability - British Car Forum

Yes, the original Ignitor module can overheat if left powered on in the conductive state with the engine not running. As the tech guys told you, ...

Pertronix Electronic Ignition Retrofit For Stock Flat Cap Red Point ...

Pertronix Electronic Ignition Retrofit For Stock Flat Cap Red Point Distributors On Land Rover Series 2, 2A, And 3 (7269 Same Fit As Part # LU-143A), ...

Pertronix wiring for booger eaters - Vintage Mustang Forums

Tonight I'm installing a Pertronix Ignitor II equipped distributor, Pertronix Flamethrower coil, and Pertronix 12V relay on my '67 C-code 289.

Electronic Ignition Conversions | PerTronix 1442 Ignitor IHC 4 Cyl

Electronic Ignition Conversion Kits to replace original mechanical points & troublesome factory ignition. Dependable, maintenance free, and easy to install.

Atomic 4 - Pertronix ignitor install - YouTube

Learn how to install Pertronix electronic ignition on your Atomic 4. Find your Atomic 4 parts at Moyer Marine: https://www.moyermarine.com.

Technical - Pertronix Ignition Problem Has Me Stumped | The H.A.M.B.

I have the original style Pertronix Flame Thrower distributor and their 1.5 ohm coil. There is no spark to the plugs; the timing light won't blink.

Anyone have any luck with pertronix ignition? - Ford Truck Enthusiasts

The Ignitor 1 works fine, it isn't going to melt down with the key left on unless you're really determined. These tales get told and retold on ...

Pertronix Ignitor: with or without new coil? | ClassicBroncos.com Forum

You can use a Flame Thrower I coil with a Pertronix II module. Your coil has to have an equal or higher rated ohm resistance.

Issue with Pertronix Ignition System - V8buick.com

A pertronix 3 (reall kickass unit) must use a low resistance coil marked as igniter 3, a full 12 volts from key to coil, and use proper spark plug wires.

Need some help re Pertronix ignition | Chevy Tri Five Forum

I have a Pertronix electronic ignition and coil in my '57. It's been running great for 5 years (albeit at very low mileage, probably no more than 2000 miles ...

Pertronix Electronic Ignition Help - 912 BBS

You need to adjust the timing with the new Pertronix installed. Set it at static for about 3 degrees then go to 3000PRM and reset to about 33 degrees.

Pertronix Ignition on Ford 4000 3 Cyl - Yesterday's Tractors Forums

This Pertronix electronic ignition and coil work great. Fired up on first compression stroke. The 3ohm coils seems to work great. Easily installed.

PerTronix's New Digital HP Mobile Ignition Box - EngineLabs

PerTronix's Digital HP Mobile Ignition Box and corresponding mobile app allow you to customize several settings including rev limits and ...

Plug Wires ( Pertronix 1 - Ignitor) - FordSix Performance Forum

Any good quality supression wire will be fine. If you do like aftermarket/performance wires, You will find that most people that have been in it for a while ...

PerTronix 510C Digital HP Ignition Box and Coil Combo

The Digital HP Ignition Box is reliable, precise, and strong for quick starts, smoother idle and a quick throttle. Combine with Flame Thrower Canister Coils ...

Pertronix Ignition - Gut check | SAOCA Forum

1) Connect the black Pertronix wire to the original wire from the ignition switch 2) Connect the B/W wire to the Coil Neg 3) Connect the coil Pos to the ...