Events2Join

Rattling sound when car is placed in gear


Rattle sound at low speed in 1st and reverse

I hear a pretty bad rattling sound when backing up or starting out in 1st gear. ... Car idles rough and makes rattling sound in neutral · 6.

Rattling under car in gear... | Focus Fanatics Forum

More likely than not it's a heat shield that's rattling around, it's pretty typical to hear a rattle noise from those at only a certain engine ...

Rattling Noise when Transmission is in Drive (D) - Bimmerpost

I launched the car last night and when I got home, I realized a rattling noise from my car. I put the car in park and the noise went away. Put it back in ...

rattling noise when shifting gears - Geo Metro Forum

Sometimes the shift linkage is too close to the catalytic converter heatshield and makes contact, resulting in noise under certain load conditions.

Rattle sound when in gear - Toyota 4Runner Forum

Could be your exhaust tip rubbing against your hitch if you have one equipped. Or it could be the inside of your muffler broken loose and rattling.

Rattling sound on drive or reverse - New to Forum | The Nissan Club

Your slight rattle in reverse is likely just an exhaust heat shield that's loosened. Standard decade-plus practice is to put a 6" stainless gear band clamp ...

Q: Rattling noise as I change gears and accelerate - YourMechanic

Exhaust systems are commonly hung from the vehicle using rubber hangers. If any of those hangers are stretched or broken, it can cause rattles, ...

Rattle at idle in gear | Acura TSX Forum

Tried a few times. Put the belt back on, start the car, put into drive. noise is back. So it has to be belt/pulley related. Its a ...

3rd gear rattle | Access Norton

if it is a rattle in just one gearit is VERY common for these gears to shed teeth. IMHO i would be going inside for a look before more damage is ...

Anyone have a rattle but only at specific RPM? - Toyota Sienna Forum

Your lucky you can create the noise standing still. Try reverse. If no noise, the engine rocking backward in response to being in a forward gear ...

Rattling Noise at Idle | SwedeSpeed - Volvo Performance Forum

First is a rattling/rubbing sound when the car is stopped and in gear. If I put it in neutral or take my foot off the brake, the noise stops.

My manual makes a rattling sound - Page 2 - Maintenance/Repairs

I think you have the hang of it. So it could be the exhaust system. You may have weak engine/transmission mounts. Have both checked out. 1 Like.

rattling sound when going into gear? - CamaroZ28.com

does anyone know of the rattling sound every time i put my car in gear or when it shifts? sounds like a cable bouncing around but only when the ...

rattle while engaged in gear? - Volvo Forums

RE: rattle while engaged in gear? You need to isolate where the noise is coming from. For instance, I had a car with a nasty loud rattle in idle ...

Rattling in transmission when I put in gear. | Club Sea Ray

The noise or rattle marble sound is coming from the dampner plate between the engine and trany. The springs get a little loose over time and ...

rattling noise, only when in gear. Not there in park or neutral.

I am hearing this rattling noise (sounds like a pully but it isn't) only when in gear at idle or low speeds (I can't tell if it is making noise at high speeds, ...

3rd Gear Rattle Noise | Ford Focus RS Forum

Yes, I can stop the rattling by holding onto the shifter too but this is a brand new car and things like this is not acceptable to me. The noise ...

clutch noise in neutral - StandardShift.com

Neutral Rattle isn't a problem beyond how much the noise bothers you. There also was a thing called gear rattle that was a problem when Chrysler first started ...

rattling noise on 3rd gear accelerating - RX8Club.com

Face the problem of metallic rattling nose on 4th gear when stepping on the gas, especially when car is at 60-80 km/h. Have read several similar ...

Grinding sounds when placed in gear | Taurus Car Club of America

When you put the tranny in gear, you're also putting a load on the engine. Are you sure the noise isn't coming from a component bearing on the ...