Applying Waterslide Decals Correctly
Anybody Make Waterslide decals? - Unofficial Warmoth Forum
Apply a medium wet coat of lacquer, dry an hour or more. Apply a medium wet coat of lacquer, dry a day. Use 600 or 800 grit paper to level out the finish over ...
Is Waterslide Decal Paper Permanent? - Yesion
To ensure the longevity of waterslide decals, make sure to apply them to clean, smooth surfaces free of dust and debris. Avoid touching the ...
Applying Waterslide Decals Made Easy - YouTube
Well, that important stuff is when you showed us painting the decal in pure water after you apply it to get it in the right position. That is a ...
Best techniques for applying decals? - the MRH Forum
You can use the setting solution of your choice with our decals, Micro-set/Micro-sol, Champ Decal Set, and Solvaset all work well. · Apply decal to a gloss ...
Putting on a water slide decal ? | The Gear Page
I'd spray the tint coats.. if you want a vintage look, let it dry thoroughly, then apply the decal.. give it a few hours to be certain the water ...
Waterslide Decals and Flat Paint | Rocketry Forum
Basically, only a small percentage of the decal is actually touching the paint, the rest is above the voids between the high spots on the ...
Making Waterslide Decals | SlotForum
2) Once you print them, leave the ink to dry for a whole day before aplying sealer or clear coat. 3)Once the clear coat is aplied, again leave ...
I carefully cut out my decal as close as I could to the outer edges of the design and followed the directions for the Microsol/Set route and used that to apply ...
Waterslide decals-cleaning after application - Model Cars Magazine
You have applied your waterslide decals, but notice that there is some water staining and dried decal glue residue.
Water slide decals vs self adhesive for restoration..which would you ...
With waterslides, they apply best to a glossy surface, either the paint, or a gloss clear, then after applied, another clear coat is applied to get the desired ...
Writing On Decal Paper ! - Rodbuilding.org
This is the process I used successfully for 30 years as a kit model builder and model railroader.as a method for water slide decal application.
Waterslide Decals - "Print and Cut" Jigs with the Glowforge
Also.. why did I do what I did below? Why? Do not try and apply a decal larger than your surface – it'll trap tons of air bubbles, peel from the edges, be hard ...
Dry transfer applied as water slide decals - KitMaker Network
The lettering will be transparent, and you can use a small painted decal beneath it (in the color of your choice) or you can paint a base color directly on the ...
Having some issues with Waterslide decals | Phenotype's Zoids Forum
When I apply water slide decals I always soak them one at a time, waiting until the paper falls away from the decal before I remove it from ...
Is varnish needed for waterslide decals? - Forum - DakkaDakka
Decals are essential thin layers of lacquer paint printed onto a transparent film. Once properly applied to a surface, they're surprising ...
Waterslide decal installation question | TalkBass.com
4. Wet sand until smooth, let dry. 5. The next week, apply decal. Cut out decal, soak in warm water until decals just start ...
HOW TO APPLY DECALS FOR GUNPLA [EASY] - YouTube
Pros always spray a gloss coat before a flat coat to smooth out the edges. The extra layer of gloss is extremely important because flat coats scratch and chip ...
Fender “Standard” Jazz Bass – Applying waterslide decals to the re ...
Once the decal is in the correct position – carefully mop up excess water, by dabbing over the surface with a paper towel. (Don't wipe, or you' ...
Water Slide Decal - What kind of adhesive to apply on insert?
Yes, setzkor is correct: a waterslide decal does not need adhesive. The adhesive is already there and is activated by water. So check if your waterslide ...
Clear coat over water trasfer decals - AutoBody101.com
I am trying to learn the best method for applying clear coat over water slide tranfers. Water transfer decals MUST be applied over a "smooth ...