Heater Hose and Fittings

GM Plastic Heater Hose T-Fitting(s) Broke! | BobIsTheOilGuy

Many people don't realize that these plastic parts have a finite life. They probably should be replaced at the 10 year mark.

Help finding a replacement heater hose fitting in the block | '71

The Ford part# is C5AZ-8555-A (replaced by "B") and is 5/8" OD x 2 1/2". Depending on your parts source, you may have to cut the tube length ...

Heater Hose Fitting with Weiand Stealth Intake

Heater Hose Fitting with Weiand Stealth Intake · CONNECTION, HEATER HOSE - 18599-1A - National Parts Depot · EDGE INDUSTRIAL Brass REDUCING FACE ...

Installing a lower AN Radiator hose and an AN heater ... - YouTube

... Heater hose input into my timing cover, hopefully without welding, by utilizing AutoPlumb fittings. We shall see.. We're on the tail end of ...

Heater Hose Fittings | Team Chevelle

The 5/8" hose goes on the intake, the 3/4" hose to the water pump or radiator. Feeding the heater core with a 3/4" hose and a 5/8 return could possibly cause ...

Confusion about heater hose fitting in passenger head. [Archive]

All of the Edelbrock heads use a 3/4 NPT pipe plug to seal the water ports. Simply buy a 3/4 NPT x 1/2 NPT reducing bushing and a 1/2 NPT X 5/8" hose barb and ...

Heater hose connectors - Maintenance/Repairs - Car Talk Community

No, you don't break them off, you disconnect them with a special tool you can buy or borrow at many auto parts stores for free. Similar to fuel ...

Coolant leak from heater hose fitting | S-10 Forum

This heater hose is leaking and I think its because the heater hose fitting has corroded where it seals. Do I need to replace the fitting or am I not sealing ...

Heater Hose Connector - MyG37

I only replaced the hose connector since the hoses were in good shape and I used Dorman 3/4 inch straight heater hose connector (part number: 56430).

Replace The Heater Core Inlet Connector On A 2000-20006 Silverado

Fix a coolant leak at the heater core/heater hose connection, by replacing the inlet connector on a 2000-2006 Chevy Silverado and also other ...

What fittings to connect garden hose to heater core to flush?

I'm not sure what fitting I can use to connect to the heater core hose. Hopefully something I can buy at the hardware store or Home Depot.

heater hose fitting size - Chevy Message Forum

The pipe thread size for the 3/4" hose is 1/2". For the 5/8" hose the pipe thread can be either 3/8" or 1/2" depending on the year. The older ...

Sealant on intake manifold heater hose fitting?

I tried a lot of different sealing approaches, including teflon tape, but nothing works as well or reliably as Permatex thread sealer.

3.8L Heater Hose Adapter Fittings - Buick - GM Forum

The fittings connect the heater hoses to the belt tensioner. The dealer says these parts have been discontinued and regular parts houses do not stock the ...

Water Pump - AN heater hose connection - LS1Tech.com

I have seen it mentioned about running AN fittings. Curious if anyone here has done it and any recommendations. 90 degree fitting with NPT ...

Part # help - heater hose quick connect/Not the T-fitting...

I want to replace the piece that attached to the T fitting and slides into the heater hose. I have read a lot that the part is Dorman 800-403. This part does ...

BB Heater hose fittings - Moparts Forums

Moparts Question and Answer Unlawfl's Race & Engine Tech Gen III Hemi Tech Moparts Restoration & A12 Forum Corners Are Best - Handling Tech

Heater hose fitting elbows source? - CorvetteForum

One hose has 90 degree bends molded in both ends of the hose, and one just has a 90 on one end. The factory needed the 90's to connect to the ...

pipe dope or teflon tape on heater hose fitting? - The Jalopy Journal

Either should work fine, as long as you're not sloppy. Either one could get into the radiator or thermostat if you are sloppy. You may be ...

Heater core hoses with LS motor - NastyZ28.com

I'm guessing the two fittings coming off the water pump are supposed to connect with the fittings from the heater core?