Rattle Can vs. Spray gun test

Best & toughest rattle can black paint? - FerrariChat

1. Pre-heat the part with a heat gun or heat lamp. Applying paint on a warm surface makes a big difference to adhesion. 2.

Best rattle can spray paint/lacquer? - TalkBass.com

I've been thinking Valspar or Krylon, they both look solid after some testing. I'd do reranch, but I don't want to throw too much money into ...

Rattle can spray paint tips...? - AudiWorld Forums

As far as paint thickness goes, I've gotten great results by NOT spraying the paint, but just lightly misting or dusting the piece with more ...

Can I extract paint from a spray paint can and use it in an automotive ...

Household paint that is sprayed is done either through a dedicated paint sprayer or a compressor and paint pot. I like spraying houses when they ...

Priming- Airbrush vs Rattle can - The Bolter and Chainsword

... or do you still use rattle can spray primer? I just got my Iwata ... I just got some vallejo surface primer in the mail and I'm going to test them ...

"Rattle can" paints? - Cox Engine Forum

Always spray a test patch from a new can. Out of probably 20 cans ... Might try to heat cure with a mono coat heat gun, or slide it in the kitchen ...

Rattle can paint job tips? - Adventure Rider

Test your paints for compatibility ... surface prep and some patience, Aluma-Hyde II, Duracoat, or Cerekote can give real good results.

Can I get away with a rattle can (spray paint) paint job

I would test it before I committed to it. Get a piece of metal, paint it and see how it works. Then drip some gas on it and see if it bubbles.

Blobs, blotches using rattle can - Body and Paint - AutoBody101.com

Some of the spray looks ok, but then there are places that look like someone flicked a tiny paint filled brush at it. Places where instead of ...

Paint, from rattle cans to guns...need some help here

Experience is important and I would suggest you do some testing. You tube videos on gun setup are also helpful. Make sure you do whatever you ...

DIY: An Enthusiasts Guide to Painting with Rattle Cans | F30POST

Section 2 – How to Paint These are general guidelines on how to paint with a spray can, or gun for that matter. ... test spray to ensure your ...

Rattle Can Wheel Blackout - Overland Bound

5. Test your spray paint. Shake the can vigorously before spraying. Test your paint or spraying technique in an inconspicuous area or on a piece ...

Painting on the cheap (with rattle cans) - AutoShite

For the shiter in a hurry, or just plain impatient, the heat gun can dry the paint in a minute. Be careful not to get too close though, and keep ...

Rattle Can Spray Paint - Yesterday's Tractors

What is the best kind of off the shelf spray paint for painting sheet metal. I am not set up for a gun and compressor.

Best 'rattle can' paint, fuel proof? - RCU Forums

Kit Building - Best 'rattle can' paint, fuel proof? - Hey gang, I'm looking for a little advice here. I sprayed Krylon for Plastics on a ...

Longevity of a rattlecan paintjob? - ClubRoadster.net

Rattle can paint jobs are significantly less durable, especially flat paints, and will require frequent touch ups if you want to keep the look fresh.

Paint Spray Gun - How To Pick A Paint Gun - Car Craft Magazine

There are good all-around guns that have a single tip in the 1.7-1.8mm range that can be used to spray primer and a single or dual-stage paint ...

Rattle can 101 - Tips, Tricks, and Tutorials - Model Cars Magazine

Regardless of what you use: rattle cans, airbrush, enamel, laquers or unobtanium, the key to a good paint job is NOT to move forward until the ...

The Rattle-can Follies... - TalkBass.com

For colors you can use acrylic lacquer or urethane colors (custom made rattle cans at auto paint stores). Just let it dry completely and spray ...

Rattle can?! Paint job? - Tacoma World

It looks great when you're done but the rattle can paint is very soft and it doesn't take long before it's pitted and looks like crap.