Heater Hose Fitting Broke Off In Intake

Broken heater core quick disconnects - GM-Trucks.com

So the only way to prevent this was to cut a slit down the heater hose, and peel it off of the heater core tube. Sometimes the tube had bits of ...

radiator hose connection nipple broken off. - Mercedes-Benz - iFixit

On the top of the radiator is a small plastic connection of which a hose connecting the radiator with the coolant expansion tank. this hose is ...

Broke hose while removing throttle body - Mazda 6 Forums

If you don't want to do the bypass you can just go get the right size/ length of hose and replace the damaged hose. . Cardomain l Build Thread ...

Leaky Heater Hose Repair for under $25 [ 1.5 / 5 Beer Difficulty Rating]

Like many others have encountered, this crummy hose began to leak on the connector end behind the passenger side of the engine.

How do these damn heater hose fittings come off?

I had one of those couplers to break on me and the Stealer (I mean Dealer) wanted $750/each to replace them. They told they have to remove the ...

Cracked manifold near heater hose connect area

If you can get access to rough up the area with sandpaper it will stick. My problem is that it will start leaking somewhere else. You can try it ...

Heater hose replacement: Cost? Coupler fix? - MyG37

I just decided to use my razor knife and facilitate the removal of the hoses. I inspected the all ready broken connector and as I tried taking ...

Broken fitting on water intake line, can someone give me a clue?

If it is on a straight section of 3/4 copper pipe, (example) you can possibly make a temporary fix with a heater hose section and hose clamps (basicly ...

Heater hose removal at manifold fitting ? - The 1947

... fitting in the intake manifold. I understand that they are ... But I'm afraid I'm going to strip it out or break it off... . Any ...

Aluminum intake repair - Chevrolet Corvette Forum Discussion

I screwed up and ruined the threads for the heater hose fitting on my aluminum intake. The threads came out attached to the steel fitting.

Cracked Lower Intake Manifold at Heater Fitting

Put a thin layer on the threads of the fitting and wrap some teflon tape around that, then coat the tape with more PC7. (So there's actually 3 ...

Leaking coolant from heater hose fittings? : 1992-1999

Replaced the broken plastic fitting with a metal fitting to stop the infamous intake fitting leak (lower fitting on the tensioner didnt have ...

Remove heater hose fitting from Alum intake | Team Camaro Tech

Soaking it with PB Blaster or LPS will help also. It also helps to have the manifold off the motor. But do use caution with the manifold. Don

Intake manifold thread repair...? - The Ultimate 88-98 GM Truck Forum

I would drill, re-thread and make my own hose with 8AN fittings and adapters. That way its done once and for all. I would take the manifold off though to make ...

Need Help, Pipe Nipple in block broke! - MustangForums.com

it should be 1/2"npt if it's the "nipple" in the intake manifold or water pump. You might want to go to NAPA and ask for a heater hose fitting ...

1999, 5.3L LS - Heater hose removal Diffculty

As you can see in the pic, the nipple broke off. I have the special tool to slip behind it to release the female snap fitting. But I cannot get ...

What size threads on the intake rear coolant port? - ThirdGen.Org

the TBI intake on my truck, but I need to find a hose fitting that fits into the port in the rear intake coolant passage. I broke the stock ...

Heater Core Plastic Pipe Broken-1995 3.2L Rodeo-Fixed

A little bit more of the top part remained. I might be able to splice a 1/2" x 5/8"" heater hose connector(Dorman #47081) into the plastic ...

pi intake nipple broken | Ford Mustang Forums

As long as you are careful, you can drill and tap it with a pipe tap, screw a brass fitting in it with some epoxy and let it go.

Hose coupling stuck in intake...Help! - Blazer Forum

... intake...Help! - On my 1994 Blazer I had a leak in the coolant line between the heater core and the intake manifold. I ended up breaking ...