How to configure Queuing on Cisco 3560 and 3750 switch

Configuring QoS [Cisco Catalyst 2960 Series Switches]

Switch(config)# mls qos queue-set output 1 threshold 1 138 138 92 ... Mixed Switch Stack (Catalyst 3750, 3560, 3750-E, 3560-E, 3560-X ...

3750X Poor Performance - Cisco Community

I recently swapped those switches out for 2 3750X switches in a stack, and copied the identical configuration on them as the original 3560 switches. I have ...

How large are the buffers in the output queue really when enabling ...

I'm implementing a network based on Catalyst switches. We use different models: C2960-S, C2960-X and C3120 (similar to C3750).

Traffic Shaping on Switch - Is it supported and on which models?

3560/3750 has default CoS/DSCP mappings to queue. If all your traffic has same ToS markings, only one queue will be used. View solution in original post.

Catalyst 3750 Software Configuration Guide, Release 12.2(55)SE

... Catalyst 3750 Switch Software Configuration Guide. OL-8550-09. Preface. Conventions ... 3560, 2975, and 2960 Switches. • Catalyst 3750, 3560, 3550, 2975, 2975 ...

Ingress queuing on Cisco 3560 switches

Assuming that the configuration is as follows: ! mls qos srr -queue ... 3750 , so the queues are all shared but the priority queue is ...

Configuring QoS - Cisco

In the Catalyst 3750 Metro switch documentation, nonhierarchical policy ... Catalyst 3560 Switch Software Configuration Guide. OL-8553-05. Chapter 33 ...

MLS QoS on 3560 and 3750 - srr-queue bandwidth limit

Hi experts, I feel that 3560 and 3750 perform differently with the following two commands: srr-queue bandwidth shape 5 0 0 0 srr-queue bandwidth limit 50 On ...

Catalyst 3750-X and 3560-X Software Configuration Guide, Release ...

A switch stack operates and appears as a single router to the rest of the routers in the network. Basic routing functions, including static ...

Catalyst 3750-X and Catalyst 3560-X Switch Software Configuration ...

For information about Catalyst 3750 switches, see the “Managing Switch Stacks” chapter in the Catalyst 3750 Switch Software Configuration Guide. One of the ...

3560E output drops without QOS enabled - Cisco Community

The Cisco Catalyst 3750 Series Switch supports Weighted Tail Drop (WTD) with three thresholds. ... setup default setting for egress queues and got less number of ...

Catalyst 3750-X and 3560-X Switch Command Reference - Cisco

... queue-set output buffers 2-382 mls qos queue ... This chapter describes how to use the switch command-line interface (CLI) to configure software features.

Catalyst 3750-X and 3560-X Switch Software Configuration Guide ...

A switch stack is a set of up to nine stacking-capable switches connected through their StackWise Plus or StackWise ports. You can connect only one switch type ...

Cisco switch output drops due to QoS

I'm quite new to QoS and troubleshooting an output packet drop issue on a 3750x switch which seem to be due to QoS configuration.

3560 vs 3750 ? Help Understanding - Cisco Community

The Cisco Catalyst 3750-X Series and 3560-X Series Switches support dual redundant power supplies. The switch ships with one power supply by default.

srr-queue bandwidth limit - Cisco Learning Network

I have cisco 3560, IOS v. c3560-ipservicesk9-mz.122-55.SE9, and try limit outband bandwidth to customer. Config of port is. ////////.

QoS on egress traffic - Cisco Community

If its a 3560 or 3750 then all you can achieve is egress queueing where you would typically enable egress expedite queueing and map DSCP EF to this queue.

Some help with something I am missing with my QOS and VOIP

1) Turn on QOS on all of my switches (mls qos) · 2) Tag 100% of the traffic in VLAN5 as EF · 3) Set every physical port connected to phones, VOIP ...

Catalyst 3750-X and 3560-X Switch Command Reference ... - Cisco

... queues command B-41 debug platform device ... This chapter describes how to use the switch command-line interface (CLI) to configure software features.

cisco 2960, 3560, 3750 switch series bidirectional throughput problem

Tried to adjust interface buffers, hold queues; queue-set buffers and thresholds, no success. Maybe it is just a trivial config change that I`m not aware of ...