- Rotors won't come off!!!!!!!!!!🔍
- Rear Rotor Removal🔍
- Tip for removing stuck wheel hubs and rotors🔍
- Tip on Getting a stuck Rotor off🔍
- How To Remove a Stuck Brake Rotor🔍
- Rear disc rotors stuck ?🔍
- How to remove a freely spinning but laterally stuck rear brake rotor🔍
- What size bolt do I need to remove a rear rotor?🔍
How to remove stuck rotors
Rotors won't come off!!!!!!!!!! - Mazda3 Forums
I have 2007 Mazda 3 2.0L. I can't seem to get the rotor off. It's either stuck on because of rust or do I have to remove some sort of ...
Rear Rotor Removal | GMC Acadia Forum
Slowly turn the rotor until this hole allows you to view the star wheel for the parking brake. Use a blade screwdriver to loosen the parking brake a few clicks.
Tip for removing stuck wheel hubs and rotors - GMC Terrain forum
First, start by loosening the hub nut and knocking the axle free. You need to do this before you loosen the hub or you're going to have a bad time.
Tip on Getting a stuck Rotor off | Ford Explorer Forums
Strike the rotor with a hammer a couple of times, then remove the bolts. Tap the rotor lightly with the hammer then pull off. Reply.
How To Remove a Stuck Brake Rotor - YouTube
In this Steve's Garage video I show you my simple way to remove a stuck brake rotor. When doing the front brakes on a 2010 Mercury Mariner I ...
Rear disc rotors stuck ? | Mercedes SLK World
As you gonna bin the discs anyway, use normal hammer, hit closely to the edge, that will send nice vibrations. Like.
How to remove a freely spinning but laterally stuck rear brake rotor
However, a lot of PB Blaster, over 20 min of heating with a hand-held propane torch and a bigger rubber mallet did the trick.
What size bolt do I need to remove a rear rotor? - SOLVED!
Just tap/smack it a few times with a hammer. I usually do the face of the rotor hat then the sides as I spin it. Try not to smack the rotor face ...
need help getting stuck rotors off - MX-5 Miata Forum
Try this. Remove the caliper and it's bracket from the hub. Then run a bolt through the hole for the caliper, from behind, and thread a nut onto ...
Rotors stuck, help! | Hyundai Genesis Forum
Hit the outer edges of the rotors with a rubber mallet. It will loosen it out of the hub. I had an issue where the rotor got stuck at an angle ...
Rear brake disc rotor stuck - Toyota Nation Forum
Had to remove the winter wheels on my sister in law's Vibe a few weeks back and they were rust locked, I pounded them like crazy for a good ...
Stuck brake rotors - Nissan Forum
Re: Stuck brake rotors ... Put the wheel and tire back on leaving some looseness and hit the tire with the sledge hammer and beware of rebound. If ...
Can't Remove Rear Rotor.... Parking Brake Stuck - ClubLexus
Turn the rotor until the access hole is in the 9:00 position. If you push the screwdriver between the cogged wheel and the spring, that tightens the park brake.
how to remove rear rotors when they are stuck on parking brake shoes
Remove springs, remove pins with U spring and adjuster => this will give free play to breaking shoes.
Hammering off rusted rotors | The Garage Journal
If you hit around the edge of the top hat part of the rotor in a circular pattern around and around, it will usually loosen it. And that seems ...
Rear rotors stuck | Dodge Durango Forum
If the rotor turns and doesn't wiggle at all, it isn't likely to be the e-brake (yet). Best bit it to rig up some sort of a puller or press and then whack it ...
Distributor Rotor Stuck - Boat Design Net
Light taps at first, try to remove, then more taps. They come of easy enough, but sometimes require some "convincing". PAR Plans · PAR's ...
My rotor is stuck! help! | VW Vortex - Volkswagen Forum
Remove lugs, wheel. Remove rotor screw (if rotor screw is seized, see Method 2). Install 30mm impact socket on air powered impact wrench, or ...
Brake rotor removal (tips?) - Lexus IS Forum
Brake rotor removal (tips?) ... Rubber mallet. ... wd40 it then wait a little. Then use a mallet to smash it out. ... Dood, you need to be more ...
How to remove stuck front brake rotors - Blazer Forum
You need a three jaw, 10 ton gear puller wide enough to span the rotor diameter. There is a reason why your axle stub has a recess formed into it.