.308 case to 7mm 08 case?
Resizing brass from 308 to 7mm-08 - The Firing Line Forums
Going by the case drawings in a Hornady manual, the 7mm-08 case is 0.02" longer than the .308 win, and the case body from the base of the case ...
.308 case to 7mm 08 case? | Shooters' Forum
I would fire a 7mm-08 cartridge in your gun then measure neck diameter of that case, then make sure necked down 308 case loaded is around .002" smaller.
7mm-08 from 308 brass | Long Range Hunting Forum
Has anyone ever had any problems making 7mm-08 from 308 brass, my Remington 700 will not chamber a 7mm-08 using 308 brass. It will chamber 7mm-08 cases fine ...
Case forming process 308 to 7mm-08 | The High Road
Member ... It is very do-able by simply FL sizing the 308 brass with the 7-08 die. Annealing is not necessary but will help. Your brass will be ...
.308 to 7mm-08 | In-Depth Outdoors - In-Depth Outdoors
308 case directly through a 7-08 full length resizing die (in several stages) and you end up with…wait for it…7-08 brass. Notice the WELL ...
case neck turning for .308 resized to 7mm-08 | Rokslide Forum
I am looking at the Hornady case neck turning tool and Forrester attachment for their case neck trimmer. Will either of these do the job for me ?
Resizing Starline 308 brass to 7mm-08 : r/reloading - Reddit
Does anyone here have experience necking Starline 308 down to 7mm-08? If so, how did it go? I have necked down 10 cases so far, ...
Neck Down 308 to 7mm-08 - YouTube
Back At The Bench 030423 Converting 308 Brass to 7MM-08 Brass ... CONVERTING 308 MILITARY BRASS INTO 243 (CASE CONVERSION). Wayback When•16K ...
Forming 7mm-08 Rem Brass from Federal Brand 308 Win Brass
My 308 brass is once fired. I will resize cases in a 308 Win die and then run the cases into a 7mm-08 Rem resize die. Then I will trim cases ...
Back At The Bench 030423 Converting 308 Brass to 7MM-08 Brass
I'm converting some 308 brass to 7mm-08 brass. That's a good excuse to use the Burstfire case annealing machine to soften the case necks ...
Resizing Cases : 308 to 7mm 08 | The Stalking Directory
Yes, you can resize down to the 7mm. Whether you'll get away without turning the neck will depend on your chamber but you'll likely have an ...
Necking down .308 brass to 7mm-08 in one go - Enough Gun
Yes, you should be able to do it in a single pass. You might lose a few cases if the odd one crumples, but it shouldn't happen often.
Questions about Case forming 308 to 7mm-08
I use at least two steps of expanding mandrel to make that change, sometimes 3 steps - 25cal, 6.5mm, then 7mm. The more you ask it to expand at ...
308 to 7mm-08 brass: Neck thickness? - 24hourcampfire
It would have worked out if I started with WW brass which is the thinnest in the neck of the 308 cases I've tried. You really want to use a ...
Can you resize .308 brass to 7mm-08 cases? | 1911Forum
308 cases are short, you may not need to trim them after they've been necked down to 7mm-08. If the .308 cases are near SAAMI Max spec in length ...
Can you swap a .308 barrel with a 7mm-08 barrel and ... - Quora
The 7mm-08 winchester is a .308 winchester that has been necked down to 7mm. The head dimensions are the same, case dimensions aside from the ...
Necking down 308 to 7mm08 - NZ Hunting and Shooting Forums
You should be GTG, another check is to make sure a projectile will fit easily into a fired case before it is sized. If either of those don't ...
Reloading 7mm-08 Remington Video 2: First Step…Use ... - YouTube
In this video I continue to go over the process I'm following to convert Starline .308 Win brass into 7mm-08 REM brass.
Turn .308 brass into 7mm-08 brass - The Firing Line Forums
Why not neck up? Say get 260 or 243 brass. The think you might encounter necking down is that neck thickening and require you to ream the case neck on the ...
243 brass into 7mm-08 ?????? | Shooters Forum
308 Winchester necked down to 7mm is a 7mm08, a 7mm 08 necked down to 243 is a a 243 W. Necking a case down lengthens the neck, necking the ...