Angle aluminum as straight edge for table saw jointing?

Angle aluminum as straight edge for table saw jointing? - Lumberjocks

To get the channel to be perfectly straight, I used a shallow groove, that the channel just fit into, but also kept my 72" level tight against ...

Has anyone ever tried using an aluminum angle as a cheap saw ...

Edge-sight a board, I use anything over 1/2" x 1" (12 x 25mm) and clamp securely, then use a circular saw. Always ended up straight enough for ...

Reference straight-edge - FineWoodworking

I have a Lee Valley 24 inch aluminum straight edge. I use a piece of 48 inch aluminum angle iron from the home center for longer things. I have ...

Three Methods To Get A Straight Edge With Your Table Saw and ...

Jointing Without A Jointer - Three Methods To Get A Straight Edge With Your Table Saw and Router. 2.1K views · 7 months ago ...more ...

straight edge jig - Router Forums

I saw somewhere a method of attaching an aluminum angle to a board (permanently ?) to produce a portable straight edge for jointing long boards.

Straightedge for jointer setup? [Archive]

I would want the straight edge at least as long as one table, use it to check each table for flatness. If they're flat then adjust them ...

Inexpensive straight edge - NC Woodworker

To add on to the home center metal tools of mass accuracy, aluminum angle iron, 1/2 or 1 depending on how well you are conneced to donald trump.

Infinity Tools 46" Aluminum Straight Edge

The 46” length of our anodized aluminum straight edge is extremely useful for setting up machines, making sure your jointer and planer tables are parallel.

Jointing a Straight Edge on a Table Saw with the MICRODIAL ...

http://www.microjig.com Use the MICRODIAL Tapering Jig by MICROJIG to joint a straight edge on large lumber.

How to make a straight edge jig for the table saw //jointer ... - YouTube

Subscribe! https://goo.gl/Co1oRz Instagram https://www.instagram.com/_natelarge/ Patrion - I should set one up? comment if you think so ...

Straight edge for setting up a jointer | Woodworking Talk

The aluminum straight edge I use was just a few bucks. ... Then I tested the one I bought on my table saw when I got home and found it to be ...

straighting an edge - Shopsmith Forums

Using the same straight edge approach, I might then clean that edge with a router rather than the jointer. I now have something I can work with on the table saw ...

NO JIGS! -Turn a table saw into a jointer to straighten boards!

How to straighten an edge on a jobsite with just a table saw and a scrap of plywood. ▽EXPAND THIS SECTION FOR MORE RESOURCES RELATED TO THIS ...

Getting a straight edge on a board without a jointer

Then I set the fence on the tablesaw to just reach the board I am putting the straight edge on. To save as much width as possible, I often take ...

Long Board Jointing Sled - Jig & Fixtures - Wood Talk Online

5" extruded aluminum as a straight edge for a jointing jig to use on my table saw? 51D+XtImE7L._SX342_.jpg. Quote. Link to comment. Share on ...

Make a straight line cut / edge jointer jig for your table saw - YouTube

Sometimes you need to cut a straight line, but your board doesn't have a straight edge. It's dangerous to run a curved board on a table saw, ...

Using a table saw as a jointer for long boards

You can use a long sled on the table saw or stick a long straight edge on it using double sided tape and use that straight edge as a reference on your fence.

The World's Greatest table saw edge jointing jig - YouTube

... edge jointing sled so you can straighten out the edges of a board and end up with perfectly straight and parallel edges that are ready to be ...

The Custom 46" Straight Edge for Machine Setup and Woodworking ...

The 46” length of our anodized aluminum straight edge is extremely useful for setting up machines, making sure your jointer and planer tables are parallel.

6 Simple Ways to Joint a Board without a Jointer - KM Tools

HOW TO EDGE JOINT A BOARD WITH A TABLE SAW ... This method uses a straight line rip jig, which is a flat board that rides in your table saw's ...