Brake rotors won't budge...Advice from anyone that's swapped them ...

The only advice I was given was "use a bigger hammer" until someone finally told me this trick. It worked great and has been in the arsenal ...

Having trouble removing the rotors, does anyone know what this ...

Just bang it with a hammer and it should come l lose. If you keep struggling there are two small bolt holes above and below the axle nut that ...

Front rotors loose... but then won't come off. | BobIsTheOilGuy

Push the rotor back onto the hub, spin it, then repeat several times until the rotor is off. If you have air tools available, use an air hammer ...

Rotors won't budge need help! - ClubLexus - Lexus Forum Discussion

Locate the rubber grommet on the rotor hub and remove it. Stick a flat head screw driver in it and turn downward(if I remember correctly) to ...

HELP! Brakes stuck on...Just changed my rotors, now my car wont ...

I can't get the car move. I'm hoping it's just some small step that I missed. Any suggestions would be really appreicated. Could the e-brake ...

Easily Remove Stuck Rusted Brake Rotors on any car or truck

Welcome to F Thirty3! This is the easiest way to remove stuck rusted rotor discs on your car or truck. This will save you so much time and ...

I just changed all of my rotors and brake pads but I still don't ... - Quora

Changing the pads won't change the feel of the brakes (assuming that you change them to the same model of the same manufacturer). The fix ...

Most Common Brake Installation Mistakes! - YouTube

I don't think putting the pads on backwards is a mistake,I think it's someone who shouldn't be taking the wheels off ever period,lol.

Please Help!* - new rotors won't mount to hubs!! - Saab Central

Jack the front of the car up, run the car in 2nd gear at idle and take an angle grinder to the outer edges of the hubs to turn them down till they fit.

Replace or resurface warped brake rotors? | BobIsTheOilGuy

Thickness variation is caused by run-out in the rotor when it is mounted. Run-out is caused by dirt/rust between the rotor and hub mounting ...

EASY WAY TO REMOVE A STUCK ROTOR - YouTube

Have you ever had a rotor that you simply cannot remove? Well you will be amazed how simple it can be to remove a stuck rotor!

When do brake rotors really need to be replaced?

The mechanic warned that replacing the pads without replacing the rotors at the same time would be a waste because the rusted rotors will just ...

Always put the retaining screws back in your brake rotors. - AcuraZine

What you fail to understand is that it holds it CENTERED until the wheel is bolted on to keep it all in place. This is why it is a tapered screw ...

Really, how important is it to turn the Rotors when changing the ...

And the odds of bad brake behavior, like chattering, noise, and warpage increase. In my shop, we turn or replace rotors with every brake job to ...

Rotors wont spin after new pads - - Club4AG

Try pressing in the piston as much as you can and then try again. I actually have tried, it is fully depressed. It seems like is the inner brake ...

Rotors bad after one year? | Ford Contour Enthusiasts Group Forums

Swap the rotors out under the warranty replacement, swap the brake pads and see what happens after they're bedded in properly. A lot of people ...

Brake pad/rotor replacement q's - AudiWorld Forums

The rotors wear down and are replaced normally when they dip below minimum thickness (need to look it up for you specific brakes), otherwise you can just do ...

Brake Stuck - Can't Move Forward - Maintenance/Repairs

6 weeks should not seize most rotors. You could jack up 1 wheel will it spin? eddo June 2, 2022, ...

The Case for Replacing Your Own Car's Brakes - Popular Mechanics

Blast the new rotor with brake cleaner before installing it and be sure not to touch the stopping surfaces with your oily hands, then position ...

Front brakes keep warping... - Chevy Silverado and GMC Sierra Forum

Claim that it is excessive run out, uneven wear or what ever you like. But when you take a rotor off a vehicle and lay it on a flat surface to ...