Do I have to use TRS cables for fx send/rtn?

Do I have to use TRS cables for fx send/rtn? - The Gear Page

Inserts would need a Y cable, TRS on one end, Send TS and Return TS on the other. Aux busses, record outs, mix outs, FX etc. would be fine with RTS or TRS.

using TRS cable for FX loop send/rtn? - Rig-Talk

Do any of you guys use a TRS cable for FX loop send/rtn? (to save the bulk of having 2 separate cables run to/from your amp?)

FX Loop on a stereo (TRS) cable? : r/guitarpedals - Reddit

If tip and ring channels on TRS cable have "dedicated" insulation (as in, ground shield around tip wire, ground shield around ring wire, then ...

Send/Return in TRS ? - Helix - Line 6 Community

The Helix's sends and returns are unbalanced, so using TRS cables won't make any difference. Like 1. Quote ...

What is an FX send on a mixer for? How do I use it and ... - Quora

An FX send is a channel used to isolate a group of effects for discretional use on multiple tracks. For example, maybe you want s very clean ...

Aux Sends and Returns - Yamaha Music - Blog

Aux sends are sometimes labeled with different names such as “effects send,” “FX send,” MON (short for “monitor”) or even “foldback,” but they all work the ...

Is there any reason not to use TRS cables for typically TS ...

No, for a small studio, other than the cost difference, you can use TRS in the place of TS cables. When you start looking at cable runs over ...

Why You NEED a TRS Y Cable for the HX Stomp Stereo FX Loop ...

Why You NEED a TRS Y Cable for the HX Stomp Stereo FX Loop // Plus SNAPSHOT Instant MIDI Commands! · Comments49.

USER GUIDE | Allen & Heath

Balanced (TRS) 1/4” Jack. Connect external effects device outputs to EXT RTN inputs and use. EXT RTN control to adjust FX signal level sent to main LR MIX or ...

FM3 Owner's Manual - Fractal Audio

Do NOT use TRS-to-TRS cables. > Output 2 has two options, controlled ... If you don't have XLR cables or need to use Output 2 instead ...

FM9 - 4CM and external pedals??? - Fractal Audio Systems Forum

I know I'd need some XLR>TRS cables to connect output 2 to the input of the ML10X. ... fx Loop Send) in the last loop of the switcher. The ...

CABLE CONUNDRUM - TRS vs. 1/4" ? - Gearspace

Again, if the amplifier and the effect are not internally configured for TRS effects looping, using TRS cables won't have any effect other than ...

Sending eurorack audio signals to guitar pedals (correctly) - MOD ...

The 1/4" TRS/TS cables have to be "insert type" that have a TRS plug ... I have two of the A-520s, and also use them for FX Send/Return ...

How to hook up a few effects processors to an old Tascam M312

The effects unit cables don't need to be balanced as the aux sends and returns on the tascam won't be balanced. Personally I would not be too ...

what cable to use for running effects through effects loop of my amp?

If your amp has a seperate send and return then you would need two regular unbalanced 1/4" cables. S ...

Wired for Sound: A Musician's Guide to TS and TRS Cables

Mono vs. Stereo: TS cables are your go-to for unbalanced mono signals. On the other hand, TRS cables can handle balanced mono and stereo signals ...

Can i use TRS cable for mono signal? - Engine DJ Community

Can i use two TRS cables for 1/4" R & L mono connectors to achieve stereo effect ? Like TS cables… I mean, as i know: TS is able to send ...