Do I need the hose between the intake and waterpump?

Do I need the hose between the intake and waterpump? - Chevy Talk

That hose is a bypass to allow some coolant circulation when the thermostat is closed. Its not necessary, but if you do get rid of it, make sure you have 2-3 ...

Hose between intake and waterpump - 332-428 Ford FE Engine ...

Fold the hose in half and sqeeze the middle with a pair of pliers. The ends of the hose will pertrude outward a little. From the top slip both ...

Bypass Hose from Water Pump to Intake - Team Chevelle

That hose provides a bypass for the coolant when the thermostat is closed and provides relief from air pockets in the cooling system. I closed ...

bbc,coolant hose pump to intake. - Hot Rod Forum

That hose really needs to stay put. ... thru the motor until the thermostat opens up. If it is removed (and you have no heater that flows ...

Larry Scott Asks… Is A Coolant Bypass Hose Really Necessary?

I've heard different opinions about this hose: Some say plug off the hole on the top of the water pump and forget it. Others say Chevy put it ...

Intake Manifold/Water Pump Hose Connection - CorvetteForum

I don't even think you need the bypass. You can plug both or install a water pump that doesn't have the extra nipple, and plug the intake port.

Water pump hose R&R - Ford Truck Enthusiasts Forums

No, it can't. There isn't enough room. Removing the water pump is your best and easiest bet. 66F250_4x4's ...

Hose between intake and water pump - 429-460

It is a by-pass to relieve water pressure when the thermostat is closed so, you don't blow open the heater core. Race type vehicles don't need a water by-pass.

Which Hose Should I use with my Water Pump? - YouTube

Layflat hose is very affordable but can kink. Depending on your use, you may be better using a reinforced suction delivery hose for your ...

Intake to water pump Bypass fitting - Ford Forums

This can be hit or miss as some fittings on differnet pumps and intakes can sometimes vary in length. But it may work. You also need to open up ...

Waterpump/Intake/Heater hose questions | Team Camaro Tech

Sounds as if your water pump was not designed to supply a heater core. All of my after market pumps have two fittings. The larger hose, I ...

Intake to water pump hose for air gap intake??

go over to mancini and tell them you need the intake manifold bypass hose fitting. They'll hand you the right one that is the same as stock. It ...

coolant port size on intake and water pump - Chevy Tri Five Forum

What size barb do you have on intake for bypass, if you are buying both just match them to hose. Either 5/8 or 3/4 will work here, the heater ...

Hose Between Intake Manifold & Water Pump - 500Eboard

I am getting ready to replace a coolant pump and I forgot to order the 57 mm long hose that goes from the water pump (intake pipe socket to ...

Intake to Water pump bypass hose - Offshoreonly.com

General Q & A - Intake to Water pump bypass hose - I have a gen 4 - 454 and I have a Dart intake on it. The stock intake had the bypass hose ...

Waterpump bypass hose - 460 Ford Forum

What would happen ifI plugged up the bypass port between the waterpump and the intake. ... Sin will take you farther than you want to go ...

454 Intake to Water Pump Bypass Hose? - 67-72 Chevy Trucks

I feel your pain - I have spoken to tons of folks with the same issue. Bottom line - I do not think you are going to blow up your motor if you ...

BBC bypass hose....is it needed? - Chevy Tri Five Forum

If you don't have the hose, you have no coolant circulation in the block on warm-up with the t-stat closed. So you can get hot spots and possiby ...

Hose between waterpump and engine - Peach Parts

Hey guys, I do believe you have to either remove head or move H2O pump to replace this hose ... and you need to buy the correct hose ...

Hose from waterpump passing under intake manifold

Yes you can change it without removing the intake. It comes out on the passenger side rear of the motor. The hose is bolted to the head with a bracket.