Events2Join

Edelbrock Performer runs rich at Cruise. Any suggestions?


Edelbrock Performer runs rich at Cruise. Any suggestions? - v8 forum

The issue is that the car runs rich with an AFR of 10 to 10.5 when at cruise (12 in/hg) light throttle. I have checked the float level, changed jets and rod ...

Running rich? - Edelbrock Community Forum

Hey guys, I have the ProFlo 4 system on my sbf 331 with a race cam. I have the idle set to 14:1 and the cruise at 14.1:1 but the exhaust ...

Edelbrock running too rich - Third Generation F-Body Message Boards

A choke that is stuck in the closed position will also give you symptoms like your are having. Good luck and let us know what you find.

Edelbrock running rich | Chevy Nova Forum

How many turns out do you have the idlebleed screws? If it's running rich all the time, either get fatter rods or smaller jets. Maybe even ...

edelbrock 1406, running way rich, how do i tune them?

Start by chking your float levels and fuel inlet needle and seat. Pull the jets (really easy to do) and see what the sizes are compared to what the carb ...

Edelbrock AVS running rich. - Team Chevelle

Geoff gave you great advice regarding manifold vacuum advance. You'd be wise to follow it. Get a longer hose. Most likely the throttle blades ...

Why would my carb start running rich at idle and while driving

When someone has an edelbrock that is mysteriously running rich, the first go to is fuel pressure. Edelbrock carbs can't take ...

Edelbrock Carb Running Rich - Hot Rod Forum

Since your complaint is at idle I assume you run better off-idle. Your vacuum readings would be a red flag for a Holley with a normal power ...

Way too lean coming out of cruise - Edelbrock Community Forum

The swing in AFR from lean to rich is common on decell. If it is stalls on a decell you may want to verify that the idle screw speed is set properly.

Running rich on A/F gauge with edelbrock 1406 - CorvetteForum

I think your afr's are just fine. Idle is fine as long as the idle is steady. Cruise is fine also if it's not showing any signs of leaning out.

Edelbrock 1406 Running Rich - Chevy Message Forum

The spring is essentially setting the vacuum point where the carb goes from cruise to power. A high number (8) means you to to power when the ...

Edelbrock 1405 carb rich idle - NastyZ28.com

That Edelbrock's can take no more than 5 psi of fuel pressure. I'm running the stock mechanical fuel pump, I haven't put a gauge on my fuel line ...

Edelbrock cruise tip-in throttle stumble - Vintage Mustang Forums

It would be normal to go a little rich at the pump shot since you're squirting extra fuel into the engine. Have you checked your ignition timing and vacuum ...

Running rich w/ an Edelbrock 600cfm? | Ford Muscle Cars Tech Forum

you need a strip kit for what ever model Edelbrock is comperable to your Carter. EDL-1479 or EDL-1487 that kit will include several different ...

302 Running Rich | ClassicBroncos.com Forum

If the problem is at idle, then changing springs, metering rods and jets won't (shouldn't) have any effect. Also consider a lean idle misfire.

Edelbrock carburetor running rich - Vintage Mustang Forums

3. attach a vac gauge ( manifold vac) with your idle at or near 750-900 (?) adjust each mix screw for the highest vac reading, all the ...

Edelbrock carb running extreme rich ??? - Chevy Message Forum

Whether it's a new or used carb, you've got to strip it down and clean out all the ports, bleeds, jets, orificies, etc. A plugged air bleed ...

edelbrock 600 running pig rich. Need some ideas - The 1947

Metering rods and jets are for cruise/power circuit. They should not affect the idle at all. If your into the primary circuit at idle you have ...

Edelbrock running too rich,can't fix - The Jalopy Journal

Any excess fuel overflows into the carb venturi, richening the mix. Continue this over time with poor fuel quality (is there anything else ...

Edelbrock carb a tad bit rich yet? - IH PARTS AMERICA

May be from rings that have not seated or from a non firing cylinder. What is your fuel pressure at the carb inlet?? 4-6 psi at idle. I would ...