Edge jointing cupping re|visited

Edge jointing cupping re-visited - Shopsmith Forums

Having the blade thus too high referenced to the outfeed table likely is causing the issue(too much removal of board in the center due the ...

Cupped Jointer Results | Family Woodworking

If they're not coplanar, then I'll be heading into unfamiliar terriroty. ... Edge jointing 6/4 dry hard maple and walnut, and both showed similar ...

Edge Joining Woes - Cupping At Clamp Up - LumberJocks

You should be using 2 cauls on each end (top and bottom), and 2 clamps on each end. If you have enough clamps, you could put flattening cauls in ...

I'm wondering about problems edge jointing boards together ...

As long as they're set up properly, a few passes on whichever side of the board is more cupped will make that side flat. ... You'll have a much ...

Joined boards cupping - The Wood

Then re mill the boards and try again. ... If the whole assembly is cupped across its width due to bad edge jointing I would expect you to see ...

using a jointer on a cupped board - FineWoodworking

The idea is that the strip helps the board not rock, and you joint both the strip and the cup together. Any other ideas that would help me not ...

How to fix an already glued up 2 2x12 fir boards that are cupping?

I'd rip the joint apart the rejoint the edges and reglue. When you ... re all full of pencil indentations. I had planned on a blotter ...

Advanced Edge Jointing Techniques with a Wood Jointer - YouTube

The wood jointer is arguably the most important machine in the woodwork shop because it is the foundation of all the wood you use that is to ...

Dealing with a cupped top? - Woodnet Forums

Semper, are you sure this isn't related to imperfections in the edge jointing? ... re always going to be worried that it will warp again ...

Ripping and Re-Gluing to Limit Cupping - Woodweb

However, unless the edge of the individual boards angle upward with the cup, you will get a "w" shape. Imagine letting the two halves cup on the bench, and then ...

How to prevent cupping (warping) of resawn wood - UK Workshop

I am trying to edge joint some american white oak boards together ... If you're looking to get 2 x 10mm boards, you will have to start ...

Bench Top Edge Jointing [with Video] - The English Woodworker

Is the edge square to the face of the board?? Is the edge out of twist along its length?? Is the edge bowed or cupped?? And perhaps most ...

Quick woodworking tip: When edge-joining boards together, don't ...

... cupping in your ... Here's a quick tip for any wood project where you're edge joining boards together.

Topic: Resawing and cup - Woodworking Masterclasses

... cupping. A common ... You don't need it perfect for a good resaw but you don't want any twist either, then joint one edge square to the first face.

Newb Glue-ups slightly cupped. Rip and redo or mow down on drum ...

6” for rip kerf and and edge jointing, but don't have enough meat ... One thing I can add, though, is watch the glue you're using, especially on ...

How to Use A Jointer - Woodworking Shop Class - YouTube

In this video, we get back to woodworking basics. I demonstrate how to use a jointer to take a cupped, gross board and turn it into a board ...

Jointed boards cupped | LumberJocks Woodworking Forum

Worst case scenario, you may have to rip it apart, let the boards acclimate, and re-glue. ... edges you didn't cut a dado, it's a groove.

Top Jointer Technique - Woodsmith

A cupped board is the simplest problem to take care of. Joint the workpiece with the cup facing down. The edges give the board a solid stance.

Edge Jointing Wood Without a Jointer - One Project Closer

This is an important step because even small gaps, bowing or cupping can eventually cause a glued joint to fail. Jointing both edges ensures ...

How to Eliminate Cupping? - Woodworking | Blog | Videos | Plans

Flatten each separate board on the jointer, then re-cut the edge, either on a table saw or jointer, so that the edge you plan to glue is at 90 degrees to the ...