Engine Hoist Long Enough to Put Engine in From the Front?

Rather than a floor-base......use 6" by 6" by 8' long beams placed parallel to the car with trusses similar to the top trusses in the photo to ...

Not enough reach with engine hoist - CK5.com

I removed the front wheels n tires and set the front ... I'm guessing the hinges have enough movement to clear any engine pull as long as you can ...

Engine Hoist Arm Not Long enough.. What have ya'll done? Jeep 2.5l

Do the same at the front to prevent it sliding backward. Drill another hole through the square tubing, and install an eyebolt so you can hang ...

Engine Hoist Too Short [Archive] - Pro-Touring.com

Obviously put the legs down. I would hook it from the front using a chain across the heads diagonally, knowing it was going to swing forward as ...

Harbor Freight Hoist too short? - For B Bodies Only!

Buy the load lifter. It will shift the engine back a whole bunch. Also shorten the chains don't bolt them up to the end loop so the load lifter ...

2 ton hoist - 2" too short... get it from the side?

I used a come-a-long to pull the engine/transmission back into place. I also put a piece of foam rubber on the front bumper to keep from ...

Pulling engine-hoist too short - NastyZ28.com

Are there extended versions of this lift? I certainly do not wish to remove the entire front clip. Last edited: Oct 8, 2013 ...

Engine hoist too short, or what? | Factory Five Racing Forum

Now fast forward 2 years and I'm trying to install my new engine tranny combo. But now I cant get the hoist to move far enough (from front to ...

Engine hoist for lifting? - Pirate 4x4

I have a floor jack, and can't quite get it to go high Enough to get my jacks under it. I've tried 4x4's and they keep slipping off.

Is a 1 ton crane sufficient for engine and transmission removal and ...

Depends on the engine and trans you are removing. Also make note of the lightest setting on the hoist. When the arm is extended all the way ...

Lifting car with engine hoist? - LS1Tech.com

... hoist it high enough for me to put some jackstands under it. Oh well its done now. Tags automotive, bad, body, car, engine, front, half ...

trying to put the motor and trans back in and my hoist arm is too short ...

(I think the jack stands were on their lowest/shortest notch). I then went in at an angle: line the vertical arm on the hoist up with the front ...

Northern Tools engine hoist long enough for a TR?

I have the same engine hoist. The engine lift has a factor of safety on it. Cover your bumper with a piece of cardboard to prevent scraping.

my engine hoist is too short! - ThirdGen.Org

... front bumper assembly all off? formula14's Avatar. formula14 01-22-2002 04:25 PM. Junior Member. Do you mean it doesn't have a long enough reach ...

advice about pulling an engine | Team Camaro Tech

The first picture kind of shows how far back the hoist is when it is forward all the way. about 16in back from the carb, where I'm assuming is ...

Engine Hoist lifting height : r/harborfreight - Reddit

I'm thinking of putting it on a platform if necessary to pick the engine, pull the boat ahead, take the engine off the hoist, attach the new ...

Rigging for engine hoist | Jeep Enthusiast Forums

Unfortunately it looks as though the HF Engine Hoist is a tad bit undersized for the job. You need at least 36-38" reach from the front of a CJ ...

Engine hoist wont reach! help!! - MustangForums.com

I extended the arm as far out as it could and only reached to about the front of the engine. and at that extent, the hoist can only handle 1/4 ...

Engine Hoist-----Lift the Front of my truck?????

A three ton should be able to handle this, but also make sure you use heavy enough chains or sling-straps, and that it is attached securely, ...

Engine removal/installation - Third Generation F-Body Message ...

My issue at this point is my engine hoist seems not to be long enough to drop the engine in the engine bay!. ... front hoist wheels sideways.