Group of open/close sensors shows on/off state instead of closed/open

I created a group with all my window sensors to easily see if they're closed or open: downstairs_windows: name: Downstairs Windows icon: ...

Binary Contact Sensors Open/Closed instead of On/Off when using ...

I have binary contact sensors on some windows and doors (I believe that the device class is set correctly, if I go into the binary sensor and ...

Eve Door Sensor - Invert Open/Closed statuses? : r/HomeKit - Reddit

Another option would be to install a sensor in both the open AND closed positions, and only use the “open” position sensor to turn on the light.

Binary_sensor open/close instead of on/off - Configuration

I think you can create a binary template sensor that shows custom binary values, based on the state of your mysensors binary sensor. rpitera ...

ON/OFF vs OPEN/CLOSE & Contact item - Cannot get it to work

While they read the state when it changes, if you “touch” one of the switches in the GUI by accident, they will change - even though that has ...

Trouble with open/closed sensor readings - Konnected Community

If your device handler and Konnected app are updated, at the bottom of the screen should be a section titled "normal state" seclect this and ...

FAQ: My Sensor (any brand) is Stuck on Closed (or Open)

They confirmed the door was closed. Today's Experiment: modified the stock DTH to make it always request open/closed sensor state, instead of ...

Warning entry sensor open error - SimpliSafe Support Home

If you are sure that your door or window is not open, and the message persists, there may be an issue with how the sensor is set up. Please ...

Why Does My Burglary Zone Say It's Open When It's Closed?

Burglary zones show a fault when the circuit is no longer in a normal state. This is true of both wired and wireless burglary zones.

How to update state of contact when the state is out of sync

I have a Z-wave door sensor with a contact point for open/closed. Occasionally, the door event state does not update when the door is closed ...

Sengled Open Close Sensor needs device handler

I have a series of Sengled open/close sensors that are going offline ... rather than seeing the offline state we see in native ST. Nameless ...

NO and NC (Normally Open and Normally Closed) Proximity Sensor ...

NO or NC refers to the way that a sensor is wired and in what state its output signal will be when the sensor is “made.”

open vs closed - "reversable interpretaton option" in built-in drivers?

I've run across threads discussing reversing the interpretation of a contact sensor but I don't think I've seen an explicit request to add that as an option in ...

ALARM.COM only sends sensor notifications once after alarm ...

When system is in DISARMED state, every door sensor open/close is registered and shows up under “ACTIVITY” on website, or in “HISTORY” on ...

Door Window Sensors On/Off · Issue #794 · AlexxIT/SonoffLAN

After updating to version 3.0.1 All my Door and window sensors now read Off and On instead of Open and Closed, Very confusing when a Door is ...

Open/Close Sensor - ISY994 - Universal Devices Forum

It depends on the firmware level. My two v.40 Open/Close Sensors have a Heartbeat node. They also have an external Set button.

Door / Window Sensor 7 Pro user guide (ZWA012) - Aeotec Help Desk

Once installed, the sensor will report open or close via the Notification command class to indicate a change in state to the Z-Wave controller ...

Door sensor - open-close is backwards - Wyze Forum

I have 3 door sensors. Two of them work fine. The third one says open when it's closed and closed when open. This is probably an easy fix, but I can't figure ...

Open/Close Sensor - Insteon

When using an external sensor, Open/Close Sensor is in closed state when ... Open = Group 1 On (or off), Closed = Group 2 On (or Off). This ...

Detect when magnetic door sensor is open/closed

Yes, the magnetic door sensors work just like push button switches. You could follow any tutorial on using a button and LED to learn how to turn LEDs on and off ...