Harbor Freight Hoist too short?
Harbor Freight Hoist too short? - For B Bodies Only!
Well-Known Member ... Buy the load lifter. It will shift the engine back a whole bunch. Also shorten the chains don't bolt them up to the end loop ...
Folding Engine Hoist Too Short? | NastyZ28.com
... so I think I'll order another non-folding hoist. I was reading on the Harbor Freight website, and the boom length on the folding hoist was ...
2 ton hoist - 2" too short... get it from the side?
Remove whatever thru bolt is on the end and remove the hook. Then find some thick tubing that fits in OR around the end of the boom and slide it ...
Modifying The Harbor Freight Engine Hoist : r/harborfreight - Reddit
It did not instill much confidence in terms of how much flexing happened, but it worked (not lifting anything too heavy - maybe 100 lbs). I ...
Engine Hoist Too Short [Archive] - Pro-Touring.com
What do you do when your engine hoist is too short to reach the intake? ... This is a Harbor Freight crane, but this is their 1 ton crane and it ...
Not enough reach with engine hoist - CK5.com
I find out this hoist is about a foot too short. It's a 1 ton model my Dad got from Harbor Freight quite awhile back, apparently the two ton version (which ...
Harbor Freight Engine Hoist Modification - YouTube
However, lifting much of anything beyond the front of the legs will result in stability issues even with weights on the back wheels so be ...
Engine hoist wont reach! help!! - MustangForums.com
I purchased a one ton engine hoist from harbor freight today. When I positioned the hoist in front of my stang, the arm is about 12" too ...
Harbor Freight Engine Hoist Improvements: Modifying The Legs
I have taken an older harbor freight engine hoist and am modifying the legs so it will store in a smaller footprint. This is a 2 ton hoist ...
Secret Harbor Freight Engine Hoist UPGRADE! - YouTube
I dont know if it's actually a secret, but this combination air/hydraulic 8 ton ram upgrade for your engine hoist is a game changer.
Engine Hoist Too Short - Pro-Touring.com
... Harbor Freight engine hoist that I have. If so, i've used it to pull the small block out of my 69 Camaro and the big block out of the donor ...
Harbor Freight 2000# hoist issue | The Garage Journal
Definitely not stripped gears. When it does engage it works fine. I believe it is a result of not enough current getting through the switch to ...
Owner's Manual & Safety Instructions - Harbor Freight Tools
Secure in place using four Small Caster Bolts, Washers and Lock Washers. ... Move the Crane so that the Hook and Chain are directly above the item to be ...
Experiences with harbor freight engine hoist | Page 2
Yep the issue with the harbor freight one is lifting height. I ... Biggest issue with most lifts is the boom is too short to reach the ...
Harbor Freight 2-ton hoist: Good enough? (Page 1) — Lemons Tech
My teammate has the HF 2 ton hoist and it is built just as good as any cheap hoist, but the reach is very short. It was too short to use on ...
Harbor Freight Hoist problem · 1) There is air in the ram that needs to be bled · 2) You're getting low on hydraulic oil · 3) The ram is leaking
Modifying an engine hoist | The Hobby-Machinist
I would suggest taking a trip to Harbor freight, and take pics of their hoist. ... small casters off the floor but they are just a scoche too ...
Harbor Freight 2 Ton Engine Hoist Support Arm Fix - YouTube
... hoist arm. It seemed as if the supports were too short and it was a manufacturing defect. I later determined that the supports and the main ...
I have a Harbor Freight hoist, and the pendant control attached to it ...
... Harbor Freight hoist, and the pendant control attached to it is too short. I'd like to wire a remote control receiver to it so that I can ...
Engine Hoist Long Enough to Put Engine in From the Front?
Had the same problem of the boom being too short. I know the ... With my Harbor Freight engine hoist, I've removed the SB engine from ...