Heater hose removal at manifold fitting ?

Removing heater hose nipples Aluminum Intake - Team Chevelle

Use a torch to heat and expand the intake area around the fitting, trying not to heat the fitting. Use a six point deep well socket to screw it out of the ...

GM Heater Hose Quick Disconnect Outlet Replacement - YouTube

Thanks for uploading, I'm an old Guy and needed a refresher on this problem. I am going to put a high-quality chrome 1/2" NPT to 5/8' hose ...

Heater hose removal at manifold fitting ? - The 1947

Is there a trick to getting the old fitting out? I just got done replacing the heater core on my 87 Jimmy and was going to replace all of the hoses.

Easiest way to remove heater hoses - YouTube

Thanks for the tip! I just used the zip-tie trick on the firewall connection on my 2012 Expedition and it worked like a charm.

removing heater hose from intake manifold - CK5.com

Just unthread the heater hose nut from the fitting. This style of fitting is not made of brittle pot metal like the style that uses the snap in ...

broken hose fitting in manifold. DOH! - Chevy Message Forum

Simple job went south. Any tips on how to get the crappy pot metal heater hose fitting out of intake manifold after it's already sheared off? JT ...

heater hose to manifold fitting - Ford Truck Enthusiasts Forums

To cut to the chase: do I use thread tape on intake heater hose fitting? Just a quick question. Found a leak last week.

Any tips for replacing the heater hose quick disconnect?

Remove / delete that fitting and install a hose nipple. Same thread as your garden hose. Delete fitting, install hose on nipple with ring gear clamp. The end.

Can't Believe This Was Installed In MY TRUCK!! Heater Hose Quick ...

How To Replace Your Car or Truck's Heater Hose Quick Connect Fitting With a Brass Fitting!! ... Can I Save This Intake Manifold? Severe ...

GM Removing Coolant Quick Disconnect Fitting Stuck In Intake ...

The original fitting is very weak and prone to breaking. Was going to change the heater hoses and the quick disconnect fitting just broke ...

How To Fix A Broken Intake Heater Hose Fitting On Your OBS Chevy

Small Block Chevy Heater Hose Locations!!! Rocker Pat · 25K views ; GM Removing Coolant Quick Disconnect Fitting Stuck In Intake Manifold - Bundys ...

Heater Hoses under the Intake Manifold (Replacement and Questions)

Most e36 BMWs have three heater core hoses, but a very few number of E36s with dual zone climate control have a fourth hose, which connects the heater core to ...

Removal of heater hose steel nipple from intake manifold 4L?

Aerostar - Removal of heater hose steel nipple from intake manifold 4L? - twisted and turned on mine yesterday. made about 10 revolutions ...

Heater hose connection at intake manifold - NastyZ28.com

So the radiator is being recored at BJR, replaced the heater core and the heater lines removed were Russell with AN fittings so... thanks in ...

Ford Intake Manifold Heater Hose Fitting Q&A - JustAnswer

The fitting is not threaded into the intake. It is pressed in. It is a catch 22 type repair. It can go both ways when you try to replace just this pipe alone.

Need tips for removing fitting from intake manifold - Team Chevelle

I picked up a used aluminum intake manifold, but it has a "regular" pipe nipple and cap in place of the heater hose fitting.

'67 intake manifold heater hose fitting removal ('67 289 A code)

Re: '67 intake manifold heater hose fitting removal ('67 289 A code) ... The engine is installed in the car. I cut the nipple part off and grinded ...

Need Help Removing Heater Hose Assembly Coolant Fitting - Reddit

The updated version of the manifold is still 80% plastic, but all the coolant passages are now cast aluminum.

Heater Hose Quick Disconnect to Barbed Fitting and Hose Clamp ...

... heater hose connects into the intake manifold. The problem I found when researching a permanent fix, is that no one gave enough full ...

need to replace heater hose under intake manifold - Bimmerfest

It is listed under "engine" and then "engine cooling". Unfortunately, it requires removal of the intake manifold to replace. Hope this helps.