How to configure samba to listen on more intefaces

How to configure samba to listen on more intefaces(lan+vpn)?

Hello, Is there a way to configure the samba to listen on more interfaces? Currently from the Luci can set only to 1 interface.

Configure Samba to Bind to Specific Interfaces - SambaWiki

If your Server uses multiple network interfaces, you can configure Samba to bind only to specific interfaces. For example, if Samba is ...

Multiple Network Interfaces with Samba

Server and workstation machines that are running Samba often have multiple network interfaces. Sometimes it may not be prudent to allow ...

Samba binding to multiple interfaces | The FreeBSD Forums

If Samba itself doesn't support multi interface binding, easiest and possibly cleanest workaround would be configuring Samba to bind all ...

Using multiple network interfaces (NICs) with Samba

conf or your Samba Server will not work properly. Those lines are only used if the computer is connected to multiple networks. If it is on a single network, you ...

can I bind to specific interface for different samba shares?

... set of hosts which are permitted to access a service [...] You can specify the hosts by name or IP number. For example, you could restrict ...

SAMBA | Different network interface for specific directories

Then, use 'include = smb-%i.conf' inside the smb.conf (it will be the master conf file, with all general settings and common shared folders if ...

Configure SAMBA with multiple ethernet adaptes. - Ubuntu - Reddit

It looks like that the SAMBA server is ignoring the interfaces and bind interfaces lines and trying to connect through the motherboard ethernet.

[Chapter 4] 4.6 Networking Options with Samba - O'Reilly

If you have more than one interface on your computer, you should always set ... interfaces parameter Samba should listen on for connections. Samba accepts ...

Samba talks on 1st but not 2nd interface. Any ideas? - Networking

In fact double check your IPv6. If your local name server is returning IPv6 addresses but your interfaces are not set correctly it can block ...

Multiple Interfaces - Samba Administration Guide - Linuxtopia

It will, however, send its broadcast packets over the unlisted interfaces. Total isolation of ethernet interface requires the use of a firewall to block ports ...

Chapter 8. Configuring an active/active Samba server in a Red Hat ...

The public interfaces of the cluster are the ones that clients use to access Samba from their network. For load balancing purposes, add an A record for each ...

SAMBA - How to config to listen to an ip address instead of 0.0.0.0

Hi ForumKid, when i installed samba, it's not that difficult to do. all you have to do edit the file /etc/smb.conf. here's a link that may also help to make the ...

[SOLVED] Sharing Multiple Folders on Local Network using Samba ...

I am using Linux Mint XFCE. This is my /etc/samba/smb.conf file : Code: Select all # # Sample configuration file for the ...

Samba 4.2.4_1 - nmbd listen on all interfaces | The FreeBSD Forums

Changing settings to IP addresses instead of interfaces also doesn't help - sockstat looks the same as above after configuration change and ...

Samba accepting connections from interfaces other than those in its ...

1 (2.4ghz Virtual AP from phy eth1), Interface not set in smb. Sambas smb.conf is configured, by default, with the " interfaces = br0 " and " ...

multiple servers on multiple network interfaces

config file to cause each smbd/nmbd pair to listen on a seperate network ... question, though I am considering trying it. someone successfully set up six samba ...

One interface for Samba another interface for NFS on same subnet?

I am about to install a 10GBe SFP+ dual port (Intel X540-T2) in one of my NAS box. I've been reading that Linux you can't have multiple nic ...

Samba configuration - www.ipfire.org

In the smb.conf the Bind interface "only" is set to "true", so that samba does not listen by default on all interfaces a little more security) ...

Samba Shares Across Subnets - Ubuntu Forums

I think interfaces are to force samba to listen only on specific NICs, should the server have multiple. ... # The specific set of interfaces ...