Just drilled a 1/2” hole in my new roof.

Just drilled a 1/2” hole in my new roof. - Reddit

I'm sitting here after drilling a 1/2” hole in my roof from inside a bedroom. To patch this hole what am I looking at? Getting on top of the, removing the ...

Accidentally drilled hole In roof. Ooops! - Ram Promaster Forum

Last year when installing ceiling paneling I idiotically accidentally drilled a small 1/8” hole in the roof. I sealed it with silicon and ...

Plugging screw holes in asphalt shingle roof

I would just slather the underside of the shingle patch with black roofing cement and push them into place. You can lay a brick or something ...

Hole Drilled in Roof - TexAgs

It's not a huge hole, to be totally honest, you could get away with putting a small piece of underlayment over the hole, and a new shingle and ...

Drilled hole through roof, doh

Get on the roof and find the hole. ... the other side of the valley, Install new shingles. Please do not just try and fill the hole with tar.

Best way to patch lag bolt holes in roof? - GreenBuildingAdvisor

If you just want a quick fix, get some of the black neoprene roofing sealant and fill the holes with it, leaving a larger "cap" area on the ...

What Is The Best Way To Repair A Hole In Your Roof?

Roofing nails are used to attach the new shingles to the plywood, then they are covered with roofing cement to prevent leaking around the nails.

Roofers: Fill drill hole in the roof with silicone?

I'd spray some kind of rubberized asphalt over the hole (the stuff you use for car rocker panels). I'm guessing silicone might break down under ...

Watch This Video Before Putting Any Holes Through ... - YouTube

... roof. The information in this video might make you think twice, before drilling holes through your roofing shingles or roofing paper. Water ...

DIY: Temporary fix for hole on the roof - YouTube

All the tools & products I used for the repair I bought at Home Depot. I cut out the existing shingles in the area around the hole.

Is it OK to drill one or two 2 inch holes into a load bearing header in ...

According to section R502.8.1, you can bore a hole up to 1/3 the width of the member as long as it is not closer than 2" to either edge of the member.

Rules for drilling holes in rafters - JLC-Online Forums

Are you just running romex? A 3/4" inch hole should be big enough, and it shouldn't matter where you put it as long as it is far enough from the ...

Roof vent and hole saw - Love Plumbing & Remodel

So if you just want to drill perpendicular to the roof, use a 2-1/4" or 2-1/2" hole saw, depending on how thick the roof layers you are drill ...

Drilling wire hole in my roof, what to seal it with? - Pirate 4x4

... my roof, i was going to heat shrink all the wire together. so idk a 1/2 hole? maybe less. But anyway what kind of plug, rubber grommet or ...

If you have a nail hole in your shingle roof, can you just pump it full ...

Most caulks do not bond well to asphalt-based products. You can make a durable repair though by filling the hole as deeply as possible with a very high quality ...

Okay to put screws into your roof? - Home Improvement - DSLReports

Usually just the friction of the screw (or bolt) entering is enough to liquify the asphalt of the shingles to reseal it. A little bit of roofers ...

Holes drilled in roof trusses - Mike Holt's Forum

See what the plumber did and follow his example. Ive been conned before on drilling trusses. Tell the contractor you need a drilling pattern ...

I'm gonna drill holes in my roof! Advice? - North American Motoring

1. Measure twice and drill once · 2. Center punch before you drill · 3. Use a new sharp drill bit · 4. Tape the surface before you drill · 5. When ...

Help! Broke a drill bit inside my rafter. How to get it out? - Solar Panels

If it went all the way through, drive it out with a punch and punch it through. . Otherwise if room, drill another hole in the bracket, and make ...

Ever drilled holes in your roof? - Nissan Titan Forum

I don't know where the overhead bag is but my guess is right up where I'm looking to drill. Now granted, I'm only drilling in there about 1/4" ...