Necking down .308 brass to 7mm|08 in one go
Resizing brass from 308 to 7mm-08 - The Firing Line Forums
308win. you're going to be squeezing down the .308 neck and this may add a little bit of length. Case necks might need to be ...
.308 case to 7mm 08 case? | Shooters' Forum
Generally if you neck down .308 brass and just shoot it you will encounter high pressure because the neck wall is too thick and can not ...
Case forming process 308 to 7mm-08 | The High Road
It is very do-able by simply FL sizing the 308 brass with the 7-08 die. Annealing is not necessary but will help. Your brass will be have a ...
7mm-08 from 308 brass | Long Range Hunting Forum
You need to neck turn. Resizing the neck from 308 to 284 results in a longer, thicker neck. You need to turn it to 13 thou web thickness. Recommend you get ...
.308 to 7mm-08 | In-Depth Outdoors - In-Depth Outdoors
308 case directly through a 7-08 full length resizing die (in several stages) and you end up with…wait for it…7-08 brass. Notice the WELL LUBED ...
Necking down .308 brass to 7mm-08 in one go - Enough Gun
Yes, you should be able to do it in a single pass. You might lose a few cases if the odd one crumples, but it shouldn't happen often. Like ...
Neck Down 308 to 7mm-08 - YouTube
Go to channel · Neck Down ... Back At The Bench 030423 Converting 308 Brass to 7MM-08 Brass ... Should You Neck Turn Brass? Lets find Out ...
case neck turning for .308 resized to 7mm-08 | Rokslide Forum
You are correct that you need to trim the necks. I have some FC 308 brass here and sized it down in a 7mm-08 RCBS FL sizing die and the ...
Resizing Starline 308 brass to 7mm-08 : r/reloading - Reddit
Does anyone here have experience necking Starline 308 down to 7mm-08? If so, how did it go? I have necked down 10 cases so far, ...
Back At The Bench 030423 Converting 308 Brass to 7MM-08 Brass
I'm converting some 308 brass to 7mm-08 brass. That's a good excuse to use the Burstfire case annealing machine to soften the case necks ...
necking down 308 win brass to 7mm-08. - 24hourcampfire
It looks like I do need to neck turn. I necked down some federal brand 308win brass. It was an easy process but like some said my necks ended up ...
Necking down 308 to 7mm08 - NZ Hunting and Shooting Forums
just run it through the F/L 7mm08 die,seat a projectile,check the neck dia.but should be good to go. Real guns start with the number 3 or bigger ...
Necking up 7mm-08 to 308 - CouesWhitetail.com
I have a friend who has done this exact thing with 100s of 7-08 1x fired brass. Worked fine. Run them through your .308 sizing die. You should ...
Forming 7mm-08; better to neck up or down?
I prefer going up. I buy .308 match brass for my .338 Federal and use an elliptical carbide forming plug to stretch the brass .030 inches to .
Forming 7mm-08 Rem Brass from Federal Brand 308 Win Brass
You should be fine unless the rifle was chambered with a custom reamer having a smaller diameter non standard neck. I know for sure one company ...
Necessity of Neck Turning - M14 Forum
I'm in the process of necking down 1x-fired Privi 308 brass to 7mm-08. I've seen where some who recommend neck turning the brass as the ...
Turn .308 brass into 7mm-08 brass - The Firing Line Forums
So, run a well lubed 308 into the 7.08 FL sizer and then deal with the doughnut that may be caused by necking down. Of course then you would have to do case ...
Reloading 7mm-08 Remington Video 2: First Step…Use ... - YouTube
In this video I continue to go over the process I'm following to convert Starline .308 Win brass into 7mm-08 REM brass.
308 necked down to 7mm | GON Forum
Yep. The 7mm-08 is nothing more than a 308 necked down to 7mm. You can use all the .308 brass that you want. As long as ...
Can you resize .308 brass to 7mm-08 cases? | 1911Forum
308 cases are short, you may not need to trim them after they've been necked down to 7mm-08. If the .308 cases are near SAAMI Max spec in length ...