Need help w/ broken choke heat tube
Need help w/ broken choke heat tube - The FORDification.com Forums
Just break or cut what's left off flush and drill it out with a bit slightly undersized vs. the tube. Once you cut through the wall the rest ...
Choke Heat Tube - Replace? - Ford Truck Enthusiasts Forums
If your original choke tubes have rusted off, you are going to have to remove the exhaust manifold from the engine and drill out the broken tube ...
Broken choke tube...... - Vintage Mustang Forums
You can run the carb with the choke completely removed, and it should run just fine once the engine warms up. Your high idle is either a badly ...
Choke heat tube - Buick - General - AACA Forums
Start with the t/stat set at indix or maby one notch rich. In COLD weather choke should open wide in 8-12 min. Sometimes the tube in the ...
carb choke heat tube in manifold help please | Boating Forum
maybe you could just coat the carb tube with JB weld and slide it in to the manifold too.
automatic choke heat tube question from a newbie
Well, if you have a knack for tubing. Just get the same fitting that goes to your carb. Maybe a female nut with a ferrule and the correct size ...
Heat Choke Tube | Chevy Tri Five Forum
Try soaking around the old broken tube with some wd-40, crc 556, pb blaster, etc., then grab it with some Vice Grip pliers and try to wiggle, ...
Help Choke Stove and Heater Tube Kit - AutoZone.com
Shop for Help Choke Stove and Heater Tube Kit with confidence at AutoZone ... broken choke heater tubes on most vehicles with hot exhaust activated chokes.
Dorman - HELP Choke Heater Tube Kit - AutoZone.com
Shop for Dorman - HELP Choke Heater Tube Kit with confidence at AutoZone ... broken choke heater tubes on most vehicles with hot exhaust activated chokes.
Pesky choke tube broken cant get it out
Use a little heat from a heat gun to encourage the stuck tube to come out, or drill it out carefully. The T fittings at the top of the carbs are vents.
Broken Choke Tubes | 348 and 409 Engines
Problem solved - used the candle trick. I tightened screws into the broken tubes and heated up the manifold around holes. I then clamped a pair ...
Choke. Heat riser tube - Chevy Tri Five Forum
You can remove the old rusted choke heater tube from the manifold by drilling out the old tube from both ends (sides) with the appropriate size ...
Choke heat tube replacement - Classic Cougar Community Forum
A piece of copper tubing with a compression fitting on the choke end works. Just get a diameter to stick into the heat pipe in the manifold.
Heat tube leak question - Buick - Post War - AACA Forums
If there is exhaust at that location then the tube that goes through the manifold is broken and needs to be replace and that requires manifold ...
Viewing a thread - Heat Riser/ Choke Tube Removal
Mike,the easiest way to get rid of the heat tube is to drill out each end.Whats left of the tube will fall out.Then drill and tap for a 1/8" pipe plug.Use a ...
heat tube from the automactic choke - Vintage Thunderbird Club ...
If your tube is broken or rusted out as many are NAPA has a replacement aluminium choke tube kit to fix it. There are several suppliers that ...
Plugging Choke Tube - Studebaker Drivers Club Forum
Unless the tube in the manifold is damaged, there's no need to plug it. It's just a closed "well" into the heat riser passage. The tube to ...
Choke tube replacement - Y-Blocksforever Forums
How ever when I tried to take the old holley 4000 off the elbows got bumped and broke the choke tube off flush with the intake manifold. I ...
choke tube vacuum leak? - Team Chevelle
If you need/want to have an operating choke you could probably replace the black thermostat with a later model electric if desired. One thing to ...
HELP Heat Tube from Carb??? - V8buick.com
On the manifold, there is a small nipple that the heat tube attaches to. or you can buy a choke stove that attaches on a convenient place on the manifold.