Proper Technique for Applying Headstock Decal

Applying a Logo Decal to a Guitar Headstock

Because you'll have a little water around and under the decal, you can (carefully) reposition it until it's in the correct place. If it doesn't ...

How To Apply Waterslide Guitar Headstock Decals - YouTube

Full video guide on how to apply our custom waterslide guitar headstock decals. Decal supplied by www.RothkoAndFrost.com 0:12 Unpacking 1:24 ...

How to Apply a Headstock Decal - Tutorial - YouTube

Good to see the practice is alive and well. 25:02 · Go to channel · No ... Applying Waterslide Decal and Spraying Headstock Tips Luthier Video.

Headstock decal how-to? - OffsetGuitars.com

I do not recommend putting the decal on raw wood (although some people claim it works fine). It is best to apply a few light coats of ...

How To Install a Guitar Headstock Decal|Easy DIY - YouTube

I show you how to easily install your own waterslide decal on the headstock of a guitar in just about 5 minutes. All you need is a custom ...

Decal Application Pic/Tutorial | TalkBass.com

Wipe clean with paper towel, and let dry for 30 minutes before applying decal. Step 5: pre position your decal, and mark on edge of headstock ...

Proper Technique for Applying Headstock Decal

The peghead is first lacquered, applying enough to produce a flat surface. Sand flat and smooth with 600 or 800 grit, then apply the decal.

how to apply a decal to a finished headstock - Telecaster Guitar Forum

Most importantly, wet the headstock where your decal will go just before you transfer the decal. This will keep bubbles from getting under your ...

How to apply a waterslide decal - TalkBass.com

Soak it in warm water for 40 - 90 seconds. Put a drop of water on the headstock right on the area you'll be applying the decal. Do that so you ...

Installing a Custom Decal on a Guitar Headstock - YouTube

In this video I'll show you how to install a waterslide decal on a guitar headstock, with all the tips, tricks, and mistakes to avoid!

Putting on a water slide decal ? | The Gear Page

Hit the headstock with several more coats of laquer but use light coats. Wet sand and polish. As a note I finished a guitar using nitro laquer ...

Create & Apply Custom Guitar Headstock Decals Easily - Guitar Fabric

Before applying your waterslide decals to your guitar's headstock neck, ensure that your neck is properly varnished and prepared. Whether ...

How To Apply Waterslide Decals To A Guitar Headstock [Guitar Mods]

In this video I show you How To Apply Waterslide Decals To A Guitar Headstock. Subscribe to The Guitar Manifesto ...

How to apply a water-slide logo to your guitar headstock - YouTube

Tip a Tea and support me: https://ko-fi.com/devilandsons Daniel from Devil & Sons Guitars shows you how to apply water-slide transfer decals ...

The Ultimate Guide to Waterslide Headstock Decals: Tips and Tricks

Applying Waterslide Headstock Decals ... Before applying any waterslide decal, it's essential to prepare your guitar's headstock properly. Start ...

How To Apply a Waterslide Decal - Rothko and Frost

Any tint should be applied to the headstock prior to applying the decal. If the surface you are applying the decal to is porous (e.g. wood, etc.) ...

Applying Waterslide Decal and Spraying Headstock Tips Luthier Video

Some tips on masking the neck off when spraying a headstock and the application of a waterslide logo decal....I'm using Nitrocellulose ...

Self Adhesive & Ultra Thin Decal Application

1. Carefully peel off backing paper from decal · 2. Position decal on headstock or surface to be fixed to · 3. Rub down the decal from the centre outwards to ...

How to Apply Headstock Decal - YouTube

Looks really good! I usually do five somewhat light coats, drying about ten minutes between, then on the sixth and final coat, ...

Applying Decals to Oil Finished Headstock? - Telecaster Guitar Forum

I would not recommend wiping an oil finish over a decal. But you can simply spray lacquer over your headstock, and not the rest of the neck. I ...