PushConnect fittings long term reliability v/s PEX Clamps

Do SharkBite Push to connect are more prone to getting disconnected due to stress etc compared to regular Pex fittings that uses Clamps?

There's no reason to use sharkbites on that install OP, just go with pex. The softener tanks might be jarred; can be moved....that could be a ...

PEX: Is it worth replacing crimps with push connections?

If you are asking about Pex expansion fittings versus crimp fittings, that's a different discussion, and there are folks who feel that one is ...

PEX — is there still a debate on reliability? - Reddit

For my money PEX A is far and away the best. The fittings don't neck down the ID of the run like other types, it can go through dozens of freeze ...

Pex clamp or Sharkbite? - Forest River Forums

Pex are great and will probably never come loose, but as most spaces where water lines in rv's are tight and almost impossible to get a proper ...

Is It Better to Crimp or Clamp PEX? - iCrimp Tools

Pex Crimps vs. Pex Clamps: Comparison ; Cost, Relatively cheaper than clamp connections, Expensive than crimp connections ; Reliability & ...

Which Type of PEX Fittings are Best? – OutdoorBoiler.com

Crimp Fittings with Copper Crimp Rings are very low cost, and the highest, long-lasting quality. It is like getting Mercedes-level quality ...

The Pros and Cons of PEX Connections | 2020-10-21 | phcppros

Cons: Two-step process can take more time, and it can be hard to maneuver the tool into tight spaces to make the compression portion of the ...

Pex tool and fittings questions | The Garage Journal

I've always used the cinch clamps (oetiker clamps), with the Apollo clamp tool from Lowes. I think it was around $30 for the tool. Never had a ...

Pros and Cons of Push to Connect Fittings - YouTube

If you're a plumber or HVAC technician, you know that fittings are a necessary part of your job. But there are so many different types on ...

Preferable method for PEX connections? - Heating Help: The Wall

PEX is new to me so I was wondering about the crimp vs clamp fasteners. ... and loosen up over long periods of time. JohnMansolf · knownspace ...

Push-to-Connect Fittings: What They Are & The Pros & Cons!

Easy to install · Good solution for quick, temporary repairs · Removable and reusable · Used for CPVC and Copper · Have a long lifespan – Sharkbite ...

Can we blow off these PEX fittings? Sharkbite vs Viega vs Uponor

so I had Jordan make me a test rig! In this video we are testing Sharkbite Push To Connect fittings, Viega fittings, Uponor fittings, and ...

How to Choose the Right Pex Fitting - BoshartU

The trade-off is that crimp type PEX they have a thicker wall than metal fittings, since the fitting goes inside of the PEX pipe, water flow can be severely ...

PEX clamps vs crimp rings? - The Garage Journal

Both are fine. The stainless is not as pretty, but I have my suspicions that it is more reliable. Also , only one tool is needed for ALL sizes.

Pex: Crimp vs. Sharkbite? - Airstream Forums

Even copper has issues not associated with freezing. I would use crimp on copper rings with brass fittings not the plastic ones. Shark bite ...

Plastic or Brass Fittings & Which are Better? - Urban Piping

It has some good strength and can be very reliable for PEX fittings. ... Most of the products are made in China and Korea and they don't take a long time to wear ...

PEX Crimp Vs Clamp Connections - Electronics Hub

PEX Crimp Vs Clamp Connections ; Very easy to install and they are old and popular; One PEX Crimping Tool is sufficient for different PEX Pipe sizes (get a Crimp ...

PEX Crimp Fittings vs. Expansion PEX Fittings - A.Y. McDonald

Plumbers choose this piping material based on the fact that it's corrosion resistant, lightweight, very bendable, easy to join, and ...

Why PEX Fittings Leak and How to Identify the Cause

PEX fittings are more complex than the fittings in CPVC and copper plumbing systems. Leaks are often related to installation errors, ...