Question about safely cutting former propane bottle for forge

Propane is heavier than air, so leaving the tank upside down lets the propane drain out. The one time I did this we pulled the valve, and let it ...

Cutting a propane tank SAFELY - Problem Solving - I Forge Iron

If cutting with gas flame, face the opening away from you for your first cut. If the valve does not open, or you can not safely check if empty ...

Propane tank forge - purging & cutting the tank?? - BladeForums.com

How do you do that? Fill them with water maybe? Flush with inert gas possibly? How do you get the non-propane stuff in there to push the propane ...

Another forge tank question | KnifeDogs.com Forums

Well-Known Member ... Just open the valve on the oxygen bottle, and cut away. Chad ...

How to cut a propane tank/gas cylinder safely. : r/Blacksmith - Reddit

Gas cylinders are great scrap material for building propane forges, rocket stoves, quenching tanks... but cutting them may be very dangerous, as ...

Cutting a propane tank : r/Metalfoundry - Reddit

Was thinking about using a propane tank as a foundry. I do see people clean them and rinse to make sure all the propane is out then cut it.

How to Make a Forge From an Old Propane Tank for Blacksmithing

Note: Despite the picture showing the guard removed, I recommend removing the valve first, then filling it with water to displace the propane.

Cutting Open Old Propane Tanks - Miller Welding Discussion Forums

Then you can pierce with a torch. If you are nervous you can fill it with water up to the level you want to cut.

Building a New Gas Forge Using an Old Propane Tank - Part 1

Time for an upgrade. My old forge was beginning to feel it's age, and it was quite limiting in what I was able to produce using it.

How to use a propane forge - WeldingWeb

If you are running it on a 20 lb cylinder, this may be your problem. If I recall right, the fancy triangle handle ones only flow a certain ...

Building a sword forge from a propane tank - YouTube

... someone. 20:07. Go to channel · 75 dollar Amazon propane forge. Is it any good? Old Hickory Forge•545K views · 12:15. Go to channel · How ...

Another forge question . . . - The Knife Network Forums : Knife ...

... old propane bottles, their an excellent shell for a forge. ... A new tank was NO problem, but a ... I cut a 100LB propane tank off for an oil quench tank ...

Propane in the blacksmith shop - YouTube

I had a special request to discus my propane setup. I no longer use portable tanks to run my forge but instead have a 500 gallon tank ...

Building a forge from a propane tank part 1 - YouTube

Building a forge from a propane tank part 1: preparing the tank. 75K views · 6 years ago ...more. Old Hickory Forge. 61.9K. Subscribe. 1.1K.

Cutting a Propane Tank - Best Gas Detector? - The Garage Journal

Tank is then filled to capacity with water (and a splash of dish soap added) until 100% water filled. Tank is then fully drained, all plugs ...

Cutting Gas Cylinders Open Safely - HELP | MIG Welding Forum

From what I understand, you only need to vent it out to atmospheric pressure, remove the valve and fill it with water to expel the propane. Is ...

Cutting USED and NEW Propane tank? How? [Archive] - Cast Boolits

From my research, cutting in half is a **** shoot. The water method isn't 100% safe. What about NEW empty bernzomatic tanks inside homedepot?

How to Safely Cut a Propane Tank - YouTube

I often get asked how to safely cut a propane tank to make fire rings, BBQ's or anything else out of a propane tank.

Process to cutting an old propane tank | Welding Site

I guess not understanding will make for a little nervousness. Fill with water (and some soap to help clean) and slosh around. The water is ...

How to make a propane forge at home - Quora

... forge), or an old propane tank. Be careful to properly and safely remove any and all propane before cutting into it!!! ... The real problem with ...