Route traffic for specific IP's

How to route all traffic to a specific ip - Super User

You can use the static route on the PC. Open cmd with Admin rights: route add 0.0.0.0 mask 0.0.0.0 192.168.2.2 . This will make the PC to ...

Route traffic for specific IP's : r/opnsense - Reddit

I would like advice on routing traffic from specific IP's, as well as HTTP/S to an individual WAN interface. I did this before using the ...

Route Traffic for a Specific IP Over a Specific Network Interface

The routing table takes the destination IP address and applies the subnet's netmask to it. When the netmask is applied to the IP address, it ...

Routing traffic for one IP address though a specified interface

The easiest solution would be to add a second IP to the interface on the 192.168.1.86 host. ie. eth0:1 at 10.1.1.x or something. It's easy to do ...

Routing from a specific IP address - Cisco Community

Solved: I am not sure if this is possible with the gear I have or possible at all. Here is what I am trying to accomplish... I would like all traffic from a ...

How do I route a specific ip address via the default system gateway?

Your computer cannot guess the gateway's IP on its own: either you set it yourself (static configuration that you did), or you get it ...

Static routes: how to route traffic through a specific gateway

Sometimes you may need to route traffic through a specific gateway only for destinations matching a group of IPs or a subnet. Static routes are usually ...

I want to route specific traffic to a specific IP address to use a second ...

Responses (2) ... Hi, I managed to solve it. I connected the second Router to the switch. Set the IP's as shown. ... I then set a static route on the Main server ...

IP Route to one ip address - Networking - Spiceworks Community

but can i add just a specific ip address to the table ie like this ... i have got the switch command to route traffic to the TMG server it is like ...

routing traffic from one source ip to a specific wan/gateway

I am looking for a way to get all traffic from one specific internal ip address routed through a specific gateway/wan. Is such a functionality available?

How to initiate traffic from a specific IP Address? - Networking

How to initiate traffic from a specific IP Address, When two IP addresses are configured on same Interface? Ethernet adapter Local Area ...

How to route all internet-bound traffic from a specific IP on the LAN ...

I'm needing to route all internet-bound traffic from a specific IP address (computer) on our LAN to GW2. I also need the capability of easily turning off this ...

Traffic to one internet IP address to use specific interface and WAN IP

Your NAT is correct and you still need it in order to have reply back via the correct ISP. But you still need routing. Think about it - routing ...

Route traffic for a specific IP to WAN 2. - Ubiquiti Community

My primary ISP (on WAN 1) is having issues with a Facebook CDN (IP address: 182.176.35.145). I've reached out to Facebook and my ISP regarding that.

Need to route all local traffic from a specific I... - Fortinet Community

Under Routing > Policy Routes, add a policy that says traffic with any source address (0.0.0.0/0) to the following destination address (10.88.0.0/16) should " ...

Route specific IP traffic from LAN Subnet to WAN specific IP - MikroTik

Use mangle rule to mark-routing, apply this to the source IP you specify. then add a routing rule that route all traffic with this routing mark , towards ...

Routing traffic through an specific IP address (virtual IP alias)

Hey guys, I've got a few IP addresses allocated as virtual IP addresses on pfSense and I would like to have a few internal IP addresses ...

Nat traffic when destination is a specific IP Address - MikroTik - Forum

The easy way is to create a static route to 66.44.XX/32 (I assume a specific host, if it's a range, then set the appropriate mask instead of 32) via the next- ...

Solved: Re: Routing internal traffic out to a specific public IP - MX65

Hi All,. First time poster. I have 2 ISPs. ... Is it possible to route outgoing traffic using WAN2 with a specific public IP address? Would like to separate guest ...

Can i route traffic out a specific ip? - Peplink Community

Overlooked this before i ordered. We already have two broadband connections and they are both static ip's. One of our servers needs to connect ...