Should I replace the ball joints or the tie rods first?

The tie rod ends would be better to do first, then the ball joints, but I wouldn't put either off, as it will cause further wear to tires and other suspension ...

Is it worth the effort to replace the entire tie rod or just the ball joint?

If you feel any play, replace both ends. If it's tight, just replace the outer. I'm assuming you've determined that the outer rod end is shot.

needs opinion with ball joints and tie rod | WAYALIFE Jeep Forum

Do both while you have it apart, it'll not only reduce your tires wearing out fast but if you only do ball joints and leave the TRE's they will ...

If a mechanic tells you he needs to change your ball joints and tie ...

Tie rods and ball joints are one of those critical components that can compromise steering ability. Bad tie rods and ball joints should be ...

Tie Rod & Ball Joint replacement questions - the Pelican Parts Forum!

You want to replace the wedge pin in the ball joint connection. Do not reuse the old one as this pin is notoriously brittle and can break when ...

Ball joints and Tie Rods Replacement - Preferred order to change ...

I found it was easiest to disconnect the tie rod and sway bar first. (Don't be surprised to have to replace the sway bar links.. They ...

Ball Joints and Tie Rods – What's the Difference? - MOOG Parts

The ball joint and suspension system can perform that function independently of the steering system and tie rod ends. However, the tie rod needs the ball joint ...

Ball Joints Vs. Tie Rods: What's the Difference? - JEGS

The small ball joint is where tie rods tend to fail, so there can be some confusion between ball joints and tie rods since the failure part on a ...

Should I replace my balljoints? When do they need ... - YouTube

When do ball joints need replaced? Most manufacturers state it as ... If not properly checked you might get false results. To keep tire ...

What to expect after changing ball joints and tie rods.

... tie rod ends should ... This will be my first attempt at Ball joints and would like to pick some brains about your experience replacing them.

Upper/Lower Ball Joints & Tie Rods

Just replace the whole outer tie rod.. I wouldn't worry about the inner tie rod unless there is visual damage to it.

Ball joints, Tie rod and drag link, when to replace? - JK-Forum.com

I'll likely do the work myself, if it needs it. My first question is how do know when it is time to replace them? I don't get any play side to ...

At what mileage did you replace ball joints and/or tie rods?

If not, the lower ball joints don't seem like a major project to do after, and it shouldn't require me to get another alignment. Btw, I called ...

any tips on ball joints and tie rod ends? - EricTheCarGuy

Pay attention to how you can accurately place furring strip in exact repeated locations. Do not take loose untill you have done that first. Do ...

Replace Tie Rod (Not the Ends) Ball Joints | Cummins Diesel Forum

Both the ball and socket can wear so it must be replaced as an assembly whether it is a tie rod end or a link. Since on a steering link, the ...

Do people replace inner and outer tie rods at the same time?

Just try moving the tie rod assembly in and out from the steering rack, and if there's slop, replace the inner tie rod. Tester. 2 Likes.

Ball joint and tie rod end replacement tips - LS1Tech.com

put rent a ball joint installer and remover and use that on the lower ball joint having a impact wrench is a life saver. also the top you will ...

How long do ball joints and tie rod end last? | BobIsTheOilGuy

Find a way to compress them (pry bar, jack, etc). If they move more than about 1/32' they are ready for replacement. Ball joints are checked ...

Replacing Tie Rods and Ball Joints Question - Tahoe Yukon Forum

I'd do it all at once since you're going to have to do an alignment anyway. Better just one than two. Might think about the pitman arm and idler ...

How to Replace Your Tie Rod Ends and Ball Joints - YouTube

Today I replaced the outer tie rods, steering bellows, and ball joints in the lower control arms. The tie rods and steering bellows were a ...