Stiff forks after rebuild.
Front forks very stiff after rebuild - ThumperTalk
dazzabb ... possibly lower legs misaligned after the parts installed? Loosen the axle pinch bolts and bounce on the front forks to allow them to ...
Fork stiff after rebuild : r/motorcycles - Reddit
Whenever i go over a bump, it seems like theres no suspension at all! It is very stiff, and i can feel every little bump. What causes this?
Super stiff forks after seal replacement? - Honda VTX Forum
Only if the axle spacers are incorrectly installed. you could try removing the front wheel and compressing the forks individually to see if the ...
Fork really stiff after rebuild. Help plz! - SOHC/4 Owners Club Forums
I managed to successfully rebuild a fork for my CB550k. It's polished, cleaned, added progressive springs, and re-oiled with exactly 165mL of SAE 10W-30 motor ...
Looking for ideas: Stiff suspension after fork seals and oil change
Adjust your compression and rebound adjustments to zero. No compression and no rebound. The bike should feel like a pogo-stick. If it does, that ...
super fork stiction after rebuild - www.DRRiders.com
Dribble a little fork oil on top of the seals and lube the fork legs a little, one other member has a similar issue and this helped.
Forks REAL STIFF after rebuild?? | Kawasaki ZX-10R Forum
Oil level is too high is my guess, remeasure your air gap.
Stiff forks after seal & oil change on CR 250 -99 | The Dirt Bike
You may have assembled the wheel to the forks incorrectly which causes the fork tubes to bind. Loose the axle clamps, push down on the bars ...
Tech Tips: Setting Up and Adjusting Motorcycle Forks - YouTube
Comments130 ; Top 5 Dirt Bike Suspension Setup Mistakes & How to Fix Them! Rocky Mountain ATV MC · 129K views ; Dirt Bike Fork Rebuild Made Easy!
Rebuilding Your Front Suspension Isn't as Tough as You Might ...
Again, spray a small amount of silicone lubricant on the fork leg above the bottom triple-tree, then release the tension on the lower triple- ...
Stiff Forks after Reseal. - Pitstop - The Motorbike Forum
I understand what you are saying mate, but no way would new seals cause the forks to have NO SAG and need a lot of effort to compress. There ...
"Sticky" Front Forks after Rebuild - StromTrooper
If neither is sticking, your problem is alignment. Do you have a fork brace? If so, did it go on easy? If you had to force it on, it is ...
Rebuilding Dirt Bike Forks is Easy! - YouTube
//instagram.com/kincadepavich TikTok: https://www.tiktok.com/@kincadepavich In this video I fully rebuild the forks for the YZ300 build! I ...
Front forks won't compress after fork rebuild - Access Norton
I use a rubber hammer. Lets say you are facing the forks and the top right has a gap. Hit the fork at the bottom right. Usually does not need to ...
Really Stiff Forks After SE Fork Oil | V-Twin Forum
Lots of people will tell you to use heaver oil to stiffen up the front end and keep it from diving to much. However they always fail to tell you ...
CB360 FRONT FORKS TOO STIFF AFTER REBUILD - Honda Twins
Since the 360 forks are pretty simple, and I can't see any other reasons for them not to function smoothly, you either have too much oil in them ...
Just did fork seals, now suspension is very stiff
sounds like who ever did the fork rebuild has made the air gap too small.. same thing happened with my Yam R6.. mine was almost rock hard ...
First attempt at suspension rebuild gone very wrong - Vital MX
Forks are fairly easy to diagnose. More than likely you did not get the dampner rod jam-nut tightened correctly. If this comes loose, you are ...
Forks very stiff after oil change | ST1300-Suspension - ST-Owners.com
I had a little build up in one fork when I pulled it but nothing worrying. Cleaned it before filling. The forks were much "bouncier" before the ...
Bike riding rough after fork seal change - Yamaha R6 Forum
Making the dampening stiffer will also, obviously, make it a rougher ride on top of the added fork oil and make it more difficult for air ...