Traffic to one internet IP address to use specific interface and WAN IP

Traffic to one internet IP address to use specific interface and WAN IP · Source zone - LAN · Destination Zone - WAN · Destination Interface - ...

How to force traffic from specific local IP's over a single WAN gateway.

I should probably mention that my single wan interface, eth0, is configured with both my static IP's and I've set up my routing table to match. My switch where ...

routing traffic from one source ip to a specific wan/gateway

You create a firewall rule on the LAN interface which matches the source address and sets the gateway. ... internet interface, seems to not work ...

Dual WAN setup - I need traffic for one particular site to only ... - Reddit

I create a firewall rule on the LAN policy using the dst.ip address and assign the traffic to go out a specific gateway instead of the WANLB interface.

Route only traffic from specific WAN IP addresses - Cisco Community

I like the second one which points to the modem IP. The first one might work (or perhaps it might not work). But even if it does work it is much less efficient ...

Route traffic from/to a local IP address through a specific WAN in a ...

Here is a config output, hope it helps. The static mapped device is named Bulsat with IP 192.168.1.208 and has to use the interface, named WAN to connect to the ...

Set a specific IP address to a specific WAN - Netgate Forum

Make a firewall rule on the LAN interface where the specific IP resides. Set the rule to, source: The IP you want to route and then set the ...

How can I route some or all WAN traffic through a backup WAN?

This article explains how to route the Internet traffic for a specific IP or subnet to use the secondary WAN. If you would like to configure WAN Failover, ...

How to Direct Specific Traffic to Specific WAN... - Fortinet Community

No settings are needed for WAN to LAN for this traffic, even though most of the traffic is flowing from the Internet to the user, it is considered LAN to WAN ...

Traffic from and to one Host (or Network) over a specific Alias WAN IP

You need to create an IP host of an Alias IP address and assign it under Translated source (SNAT) in the NAT rule. You may either create a NAT ...

How can I route all traffic through one interface, to ... - Server Fault

The raspberry pi wlan0 interface has IP address 192.168.2.30. The raspberry pi eth0 interface has IP address 10.0.0.1. I have configured this by ...

forwarding traffic to a specific WAN interface - MikroTik - Forum

so ok i apply your steps above and it work well ..!.however, what if i want to a specific ip address to exceed this rule, i mean from LAN2 i ...

Route traffic thru a specific wan port - Peplink Community

You can configure an Outbound policy - see below. I've selected the IP address of the device to force to use WAN1. You can select the MAC ...

ip address - Forward traffic from one WAN port to the other WAN port ...

If you chain routers A-B-C-WAN, A uses B as default gateway, B uses C as default gateway and C uses your ISP as default gateway. Of course, each ...

Route traffic to a URL over specific WAN interface? - UTM Firewall

Is there a way to pin outbound traffic for that domain to one interface, so that his IP address doesn't change? I took a look at Static Routing, ...

Solved: Fortigate Route Trafic from Specific Interface to

I would like always to route traffic from Interface "3" (Subnet 192.168.0.0/24) to ISP "WAN2" and never failover to ISP "WAN1".

How to route all traffic from a specific interface to a specific gateway ...

prepare an alternate routing table (using arbitrary table 1000). This table should contain everything needed, so will manually duplicate parts ...

Backhauling Traffic via a Socket's WAN Interface IP Address

For each gateway site, enable the site as a backhauling gateway. Then set the destination as Internet breakout and select the Socket WAN Port ...

How can I direct specific traffic through a given network connection?

If the two parts are on different subnets (with different network addresses) then you can using IP routing for all traffic to the right subnet.

How can I route all traffic from one interface to another ... - Server Fault

Yes, your task is usually done with routing and packet forwarding. NAT is only needed when some addresses are not routable. In your case machine ...