Two issues with ZEN17 sensors
Two issues with ZEN17 sensors - Universal Devices Forum
The status sensor on the ZEN17 is connected to a magnetic door sensor and reports changes in status very quickly and is very reliable. I am ...
Zooz ZEN17 strange behavior - Home Assistant Community
I just purchased two ZEN17 universal relays and am seeing behaviour like you described. I upgraded the firmware on one of them, excluded and re- ...
Zen 17 & Ecolink Tilt Sensor issues : r/homeassistant - Reddit
Make sure you change the mode parameter on the Zen 17 to the correct “garage door” code, then you MUST exclude the Zen17 and then include it ...
ZEN17 Universal Relay FAQs - Zooz Support Portal
Z-WAVE QUESTIONS · The ZEN17 - no. · You would not be able to monitor any analog sensors that are connected to the ZEN17, and any automations or scenes based on ...
ZooZ Devices - HomeSeer Message Board
I've had issues with both ZooZ devices I've purchased. 1. The Zen17 : Universal Relay (2 Outputs and 2 Inputs). The problem with it was when ...
Zen17 and Zooz Garage Door Opener - Devices - Hubitat Community
To rule out the magnetic sensors I switched from the ones i installed to the zen17 to the ones that tie into the alarm system, which is ...
Zooz Zen17 device - Ezlo Community
Two sensors and Two relays. I've been going back and forth with Zooz support and no matter what I try, based on their setting ...
z-wave js: Zooz ZEN 14 and ZEN 17 lost configuration/switches after ...
The problem For context: My Zooz ZEN 14 double outdoor plug had 2 switches configured prior to the upgrade. My Zooz ZEN 17 universal relay ...
ZEN17 Universal Relay Advanced Settings - Zooz Support Portal
2 – toggle switch (state changes whenever the switch is toggled); 3 – garage door momentary mode (for Z-Wave control );. 4 – leak alarm (water sensor); 5 – heat ...
Zen17 with Zooz Garage Door app -- relay intermittently not being ...
I don't have my relays (well, relay since I just use one of them) connected to my two sensors - they all function independently (i.e. both " ...
ZWave/Zooz Zen17 connectivity issues. Zwave help, or maybe ...
For about the last two years, I've been using a Zooz Zen17 Universal Relay to provide Garage Door Control and monitoring to (2) GDO's.
ZEN17 Universal Relay Change Log - Zooz Support Center
Home > Smart Relays > ZEN17 Universal Relay > ZEN17 ... monitoring sensors). VER. 1.10 (released 4/2022 as ... issue for parameter 2 and value 7, this is now fully ...
Zoos ZEN17 Relay Garage Door Opener with two binary sensors
... trying to use to as a garage door opener. I can toggle it without issue and have it configured for a momentary contact. How would a car…
Zooz zen17 relay/sensor - Page 2 - Runtime - openHAB Community
It looks like the default behavior of the Zen17 is to “connect” the switch through to the relay. My discussions with Zooz indicate that this can ...
Zooz Zen17 - Device No Longer Works (as of a few days ago)
I have both a zen16 and zen17 controlling different things. The 16 is controlling my pool pump and the 17 my garage door. Both are running ...
New ZOOZ App and ZEN17 Universal relay - Devices
The device registered its three properties/capabilities ZEN17, RELAY 1 and RELAY 2 as expected. But its two dry contact INPUTS never appeared, ...
Zooz zen17 relay/sensor - Page 4 - Runtime - openHAB Community
The two “real” channels (channel 1 & 2) work as expected and control the respective relays. The sensors on these two channels also work. Channel ...
How to Use the ZEN17 Universal Relay to Monitor Analog Sensors
Save on batteries while monitoring up to 2 binary sensors at one time with the ZEN17. While the Universal Relay will not report varied values, like from a ...
[RELEASE] Zooz Universal Relay (ZEN17) - SmartThings Community
The nice surprise was that after setting both input types to “Water sensor”, the two new devices did actually get created in the same room as ...
Zooz ZEN17 Z-Wave Relay Review - YouTube
... 2:01 Low Voltage Input Demo 3:01 State After Power Failure 3:17 Input Type 4:50 Invert Reported Sensor Values 5:13 Auto Turn On and Off ...