Ubiquiti EdgeRouter As Level 2 Switch

Configure an EdgeRouter as a Layer 2 Switch - Ubiquiti Help Center

The latest EdgeOS firmware includes a built-in wizard to easily configure the EdgeRouter as a Layer 2 switch and includes a VLAN Aware option.

Problem configuring EdgeRouter X as layer 2 switch

Plug into the 1st port, eth0, and log into 192.168.1.1 2. Upgrade the firmware to the latest 3. Add eth1, eth2, eth3, eth4 to switch0 under switch0's config in ...

Layer 3 or Layer 2 switch to go with EdgeRouter? | Ubiquiti Community

Layer 3 devices are only required where there are high amounts of traffic between vlans or if the link between switch and router is slow (wireless etc).

Configuring EdgeRouter X as a switch - Ubiquiti Community

I ran the WAN to 2 LAN wizzard. On the lan port area I set the IP (192.168.1.1) to the staic IP that unit will use, then unchecked the enable DHCP option.

EdgeRouter as both router and switch? -looking for a bit of help.

Eth0 is native in, passed through to Eth4, eth1,2,3 have my private VLAN ( routed through ER-X ) as native and eth4 can also be on that with ...

Ubiquiti EdgeRouter As Level 2 Switch - Den Delimarsky

Ubiquiti EdgeRouter As Level 2 Switch · Reset the EdgeRouter to factory settings. · Set your machine IP to 192.168. · Set the machine gateway to ...

Use EdgeRouter X as a switch - Ubiquiti Community

Without any complications, all I need is to extend my VDSL router 4 ports by using EdgeRouter X as an Extra SWITCH. This will give extra 4 ports from the ...

Edgerouter X SFP connected to another switch - Ubiquiti Community

You can configure the EdgeRouter as dumn (VLAN-aware off) in which case it will simply pass all the packets as they come, or you can configure it as smart (VLAN ...

New to Ubiquity - HELP with EdgeRouter X switching capabilities

'switch0' on an ER-X is the layer-3 interface to which you would assign an IP. For each additional (non-default '1') vlan created on the switch a matching vif ...

Edgerouter using Switch & Router mode - Ubiquiti Community

Yes. You can do this by enabling vlan aware mode. you will declare 2 VLANs under switch0. the lan can be on vlan 1 and the wan ...

Configuartion of Edgerouter X as simplest switch - Ubiquiti Community

The latest EdgeOS firmware includes a built-in wizard to easily configure the EdgeRouter as a Layer 2 switch and includes a VLAN Aware option. Responses (7).

Configure EdgeRouter X as switch with VLANs - Ubiquiti Community

1- huawei 4g modem for Internet . which is connected to eth0 ip 192.168. · 2- tough switch pro 8 port ,on ip 192.168. · 3- UAP pro 7 unit with static ip and 4 ...

Adopting ERX as a switch - Ubiquiti Community

1. Enter configuration mode. configure · 2. Create a bridge interface (br0) and assign it an IP address. set interfaces bridge br0 address 192.168. · 3. Add the ...

EdgeMAX Routers & Switches - Ubiquiti Networks - Invictus Wireless

Ten Gigabit RJ45 ports offer copper connectivity with PoE input on port 1 and PoE passthrough on port 10. The EdgeRouter 10X supports Layer-2 switching with one ...

Edgerouter X as a switch - Ubiquiti Community

@BuckeyeNet If the PC connected to ER-X eth4 is non vlan-aware (it probably is not), then on ER-X eth4 switch-port config, eth4 should have 2 as pvid, and ...

Edgerouter X behind another Edgerouter X to be used as a ...

The ERX in switch mode, is a layer 2 switch. L · LukasT · 5 years ago. 0. Does that mean it is not possible to make interVlan routing happen when using ERX "as ...

Using Edge Router X as VLAN Aware Switch in a Ubiquiti network

I have noticed in the EdgeRouter Switch wizard that I can make my EdgeRouter VLAN aware by configure pvid and vid for each switch port: Eth 0, 1, 2, 3 and 4. I ...

ER-12 Ubiquiti EdgeRouter 12 High-Performance Router with a Built ...

(10) Gigabit RJ45 routing ports · 24V PoE input on port 0 · 24V PoE passthrough option on port 9 · Ports 0-7 can be configured for line-rate Layer 2 switching · (2) ...

Utter Newbie - Just need basic switch & DHCP and NO WAN.

i think if you just want it function as switch only (https://help.ubnt.com/hc/en-us/articles/217990978-EdgeRouter-Configure-an-EdgeRouter-as-a-Layer-2-Switch) ...

EdgeOS User Guide - Ubiquiti

The setup wizard will set up the EdgeRouter X, EdgeRouter. X SFP, or EdgePoint EP-R6 as a layer-2 switch. Management Access. Note: Ensure that the management ...