What size bolt do I need to remove a rear rotor?

What size bolt screws into a brake rotor to remove it? - Tacoma World

The bolt size is a 4lb hammer and some percussive maintenance. ... Geeves77, WrecklessAbandon and Bagman like this. Oct 11, 2022 at 11:20 AM. #3.

Screw size/type for rotor removal - NASIOC

The thread size is M8 x 1.25 (1.25 is standard pitch for M8, so you should be able to find them at Lowe's, etc.). The funtional length required is very short.

QUICK TIP: Using Bolts to Remove Stuck Brake Rotors - YouTube

: https://youtu.be/waQg39G6eF4 The bolts needed are 8mm x1.25. Length is not super important, but it should be at least an inch or so. You can ...

What size bolt do I need to remove a rear rotor? - SOLVED!

8mm, I believe. Make sure your parking brake isn't on, otherwise you're making the job harder for yourself!

Does anyone know the rotor bolt thread size for rotor removal?

M8 X 1.25 bolt should be a standard size for those push-off hole on most rotors. For my 1998 Honda CR-V that bolt is on the parts list.

What size bolts to use to push brake rotor out? 16wrx : r/WRX - Reddit

What size bolts to use to push brake rotor out? 16wrx · Comments Section · Community Info Section · More posts you may like.

Remove stuck brake rotor, weird bolt size issue - Honda-Tech

The correct size is M8 x 1.25. So on my 1995 VX, there were old rusty rotors from some unknown source, and the right bolt (M8 x 1.25) definitely ...

Stuck rotors - bolt size to help remove them - LegacyGT.com

Of course it would be better to get your hands on some M8 x 1.25 Grade 10.9 bolts and use those. However, if you don't realize that there are ...

Remove Stuck Brake Rotor using Bolt in threaded hole. Metric 8x1.25

The bolt thread is a metric 8x1.25.

V6 AWD Brake Rotor Removal Bolt Size - Toyota Nation Forum

M8 bolt I used had between 0.5" to 0.75" thread and worked perfectly. Rotors are around 0.25" thick and all you need the bolt for is to break the rotor away ...

What size bolts to pull the brake rotors? - Lexus Forum Discussion

Sometimes you have to turn the rotor to find the adjuster. I think my bolts were close to a 5/16-18. Mine I recall were coming off easy, once I ...

Rear rotor change. Any one know what size nut you use to help slide ...

You may be thinking about threading a bolt into the rotor to help remove it. Some rotors have 2 threaded holes on them near the center. If I had ...

rotor bolt size | Toyota Tundra Discussion Forum

Yeah, there are a bunch of that size bolts on the truck, but you might bugger up the threads on them if you use them to press the rotor off.

Bolt Size for Rotor Removal - MX-5 Miata Forum

For info, the size is M8 x 1.25. That did the trick! I cleaned up the hub and slathered on copper anti-seize to perhaps avoid this the next time ...

Bolt size for scatpack rotor removal ? | LX Forums Forum

13mm & 18mm for the 4 piston setup. No need to remove any center nut. 2016 Charger SRT TorRed Best: ET 12.70, MPH 112.30 ...

Bolt size? Frozen rotor | Chevy Silverado and GMC Sierra Forum

Leave those torx screws out of the rotor when you get it off. No need for them and they only cause issues. They're only there to hold the rotors ...

What size bolt to use to remove rotor from hub - G35Driver

I was wondering what size bolt I could use to remove my rear rotor from the hub. We have a hole in the back where we can stick in bolt to take the rotor off.

Bolt size for removing rear drum - PriusChat

M8x1.25. 25 mm threaded length or more should do. The threaded holes tend to be quite rusty in my experience: take your time, screw them in, then back out and ...

Bolt size to remove rotor from hub? | Scion xB Forum

I've got a sticky rear rotor. Broke out the rubber mallet..... nothing. Tried all the metric bolts I have, but none fit the holes in the ...

Thread size of front Toyota rotor | BobIsTheOilGuy

Sounds like M8 by whatever. 25mm should be good enough. Might be worth trying a couple of sizes (two of each of course). Me, I leave 'em in a ...