cables for fx loop?
Proper cable for effects loop? | The Gear Page
I'd recommend using the best cable consistently throughout your chain - any change in cable for loops will make a difference.
Best instrument cable for FX Loop? : r/GuitarAmps - Reddit
A small spool of Mogami cable and some Switchcraft plugs will make some nice cables for not too much money, and you can make the length you want.
cables for fx loop? | Mesa Boogie Amp Forum
for racks, any instrument cable will work fine. some ppl believe trs cables are better but it doesnt make a difference. the effects on ur ...
Effects Loop Cables? High Quality or not? - forum topic
The cables in a FX loop are usually decently long if you dont want your pedals right next to the amp. So you want decent cables there.
FX Loop TRS send/return Y-cable - Henriksen Amplifiers
This cable is designed for use with the FX loops on the JazzAmp and Bud amplifiers. The TRS (stereo) end plugs into the FX loop on the amp, ...
What is 4 Cable Method & How Do You Use It? - Andertons Blog
With most amplifiers, the effects loop section comes after the preamp and before the power amp. An effects loop therefore places the preamp ...
The 4 Cable Method (4CM) - What It Is and How To Use It Correctly
The Method · RED CABLE 1: Connects your guitar to the INPUT of the Multi-Effects processor. · GREEN CABLE 2: Connects from the Multi-Effects ...
The 4 Cable Method Step by Step Tutorial and Explanation - YouTube
THE BEST FX LOOP EXPLANATION! I watched a bunch no one explained where the guitar and front of the amp cables go. Obvious if you already ...
How to Use Your Amp's Effects Loop - InSync - Sweetwater
There are two main types of effects loops: series and parallel. With both, you run a 1/4″ instrument cable from the loop's send jack, through ...
What cables to use for external stereo pedals in fx loop? - Line 6
yes you need what's called an "insert" cable. it's just a Y cable, stereo jack to the pod go and two mono to the fx. for both send and return of ...
The 4 Cable Method (4CM) for Guitar Effects Pedals - Pedaltown
Amp Effects Loop: From the preamp, the signal is routed to your amplifier's effects loop (if it has one). The effects loop allows you to insert post-preamp ...
Cable length in the fx loop - Amps - Harmony Central
The manual recommends cables of 3' or less for connections in the fx loop and I'd be looking at 40' total.
Avoid 7 Cable Method (2 amp FX loops)! - YouTube
I get asked weekly how to best run 7 cable method (using 2 amp fx loops in stereo) It can introduce noise, ground loops, phase issues, ...
Effects Loop Explanation - How to Plug it & Sound Comparison vs ...
What is the effects loop? How do you plug your cables for it? How does the effects loop sound compared to the front end? Do I really need an ...
Specialty Cable: 1 foot effects loop 'Y' cable (insert cable)
It has a TRS (Tip/Ring/Sleeve, aka "stereo") 1/4" plug on one end, which splits out to a pair of mono plugs on their own wires. With two ¼ inch mono connectors ...
Serial vs. parallel effects loop (FX loop) - BluGuitar
For a long time, guitar amps only had serial effects paths. A serial FX loop interrupts the signal path between the preamp and power amp and routes the signal ...
Cabling of FX for best signal quality (stomp box effects ... - Gearspace
It's about the cables that send the signal of an FX unit in front of you (like G system) to the effect loop of the amp and return, that can ...
Even though FX Loops can offer studio quality sound to your clean effects, folks shy away from them because of the 2 extra cables involved (send and return from ...
Effect pedal order, FX loop and 4-cable method - BluGuitar
Before a distortion or overdrive pedal, it influences the level of distortion (e.g. mid-boost), while after the effects pedal, it can significantly influence ...
Is it bad to leave the FX loop permanently connected
I want to wire my fx loops into my patchbay so that I can do some cool stuff running my pedal signal and amp signal through my outboard gear...