heater hose won't come off firewall?

heater hose won't come off firewall? - Honda-Tech

if you can get a set of pliers back (which you should, being that you got the clamp off), grab the hose with the plier and twist it. this should ...

Heater hose removal at firewall - The Chrysler Minivan Fan Club

They're usually not terrible. Move the clamps out of the way by sliding them down the hose with a pliers, then take the pliers, grip the hose, ...

Suggestions on removing a stuck heater hose??

Also you could try a heat gun it will soften the hoses and they may pull off then. I also have made hose pullers in the past. I just took a ...

heater hoses connection at the firewall - North American Motoring

When you try and remove this hose you can't rotate in any circular motion, like we normally think when removing a hose. You pull the keeper wire ...

Easiest way to remove heater hoses - YouTube

Thanks for the tip! I just used the zip-tie trick on the firewall connection on my 2012 Expedition and it worked like a charm. 5:56. Go to ...

Broke the heater hose going to heater-core at the firewall....now ...

Here is the issue...after adding pure water to it a few times to get home....basically all the coolant had been run out of the engine. I now had ...

Help! I Cannot Get The Heater Core Hose Removed At The Firewall

Take a pair of slip joint pliers, grab the rubber portion around the neck of the heater core port, and TWIST the hose.

How to Take Heater Hoses Off Like a BOSS !!! - YouTube

17:27 Go to channel How to remove GM 1999-2014 Heater hose inlet connector & replacement heater core Part # 15032062

How to remove a heater hose quick connect on a GM - YouTube

Want the tools and parts that I used in this video? Click on the amazon link below *** Automotive Quick Connect Tool- ...

heater hose removal question - MX-5 Miata Forum

Work the engine end off first, since you can be rougher with it. If the firewall end won't come off easy, grab the hose with some vise grips ( ...

Firewall heater hose junction coupling removal and installation ...

Comments58 ... I easily bypassed this by breaking the coupling and feeding hoses through.

Hose from the firewall has a hole and wasn't sure what this housing ...

If i were to remove it, i would replace the hose with a brand new one. Preferably oem. This part is the housing for the butterfly valve for your ...

How-to: Coolant Leak - Heater Hose / Pipe and Valve along Firewall

Removed pipe. Snaked new part in from the passenger side along firewall. There are two rubber grommets and two metal inserts; the rubber grommet ...

Eliminate heater hose firewall fittings? - IH8MUD Forum

Heater hose won't fit through the OEM grommet. I have considered ... My hoses go directly to the heater thru the firewall. Not using ...

Chevy Truck Heater Hose Quick Disconnect Removal DIY - YouTube

You can remove the broken connectors and just put the rubber hose back on the aluminum outlet and use a screw clamp and not use that gm pos ...

How do I access water hose from head into firewall? - Rennlist

Cut a piece of hose long enough to go over the metal tube and for the plug to go in. Put two hose clamps on, one on the metal tube, one on the ...

Broken heater core end from firewall - Maxima Forums

I lost some coolant but not much. It broke off inside the hose and there is barely enough left for me to work with. I removed the rubber ...

The heater hose conection that goes through the firewall is broken ...

The part that the hose connects to ,is the heater hose coolant nipple, and you may have to replace the entire heater core, if the part is cracked off too far ...

Heater hose removal simplified - MX-5 Miata Forum

I removed my heater hoses at the firewall using two sets of vice grip pliers. I used long nose vice grips to release the clips as per the photos attached.

Heater hose leak at firewall - CamaroZ28.Com Message Board

Any of your friends have one? If so, this is the way to go. I have dremeled off all of my clamps in my car and replaced the hoses, and its ...