how to configure samba to be visible in another subnet

how to configure samba to be visible in another subnet - Super User

You don't configure Samba to be visible on the machine, whatever the machine is plugged into, must make the other subnet visible. How you do ...

how to configure samba to be visible in another subnet - Ask Ubuntu

Try setting up port forwarding rules in your cascading router (192.168.1.100) so that the smb server can talk to the client in the 192.168.2.x ...

Enabling Samba Shares Across Subnets - Server Fault

I was curious how I could go about setting up SAMBA so that shares could be seen and used across different subnets.

Noob question about SMB across subnets : r/HomeNetworking

By default Windows does not allow SMB outside your subnet. You can enable it with a registry tweak. Take care to block SMB at your router so ...

Can't access samba shares from different subnet - LibreELEC Forum

Those who seen Mikrotik routers before will know. ... From my network knowledge, I dont see any problem for it to work, if I have correctly set my ...

Samba server share files across two subnets

You must use this option to force Samba to serve the other subnets on your network. It looks like your interfaces line in your smb.conf is ...

Chapter 7. Name Resolution and Browsing - Samba.org

First, a Samba server that is a local master browser can use the remote announce configuration option to make sure that computers in different subnets are sent ...

Chapter 6. The Samba Configuration File

(In this figure, Mixtec is another Samba server, and Zapotec is a Windows client.) Figure 6-2. Network Neighborhood showing Toltec, the Samba server. You can ...

Setup and configure Samba on IBM AIX

Alternatively, in the other subnets, add the networked printer as a new printer. ... Samba is visible in the network neighborhood of Windows ...

How to share SMB to other subnets? | TrueNAS Community

I want to share my SMB to my PC which is on other subnet. My network are below and I am using pfSense as the Router.

Chapter 21. samba securing shares - linux-training.be

To allow only specific hosts to access a share, list the hosts, separated by comma's. allow hosts = 192.168.1.5, 192.168.1.40. Allowing entire subnets is done ...

How to connect to SAMBA server on different subnet to client

Some research tells me that SAMBA does not connect to devices on different subnets and I will need to set up port forwarding. The wifi router is ...

How to access samba server from different network? - Ubuntu Forums

Regardless of your router firewall configuration, you will need to configure a WINS server to browse the two subnets in your LAN. The ...

NAS samba across vlans | Ubiquiti Community

That said, if you still want the SMB share in a different subnet, make sure ... This setup is for clients and servers using SMB directly over TCP ...

Networking Options with Samba - Using Samba [Book] - O'Reilly

In this case, only the hosts that belong to the subnet 111.222.*.* will be allowed access to the Samba shares. However, if a client belongs to the 111.222.333.* ...

Browsing Across Subnets in Samba

1. Before starting, run 'smbstatus' and 'testparm' on each Samba server to make sure there are no obvious problems with the configuration such ...

Samba Windows File Sharing - Webmin

Like all other modules that configure some server, this one can only ... If you are running multiple Samba servers on the same subnet, this option ...

How to Install and Configure Samba in RHEL09/CentOS Stream 09.

mkdir -p /training/linux · yum -y install samba samba-client · systemctl start smb systemctl enable smb · firewall-cmd --permanent --add-service= ...

Accessing a share on another subnet - Spiceworks Community

I am hoping someone can help me with a SMB Share/Routing issue. ... I put the Cisco in and set up the static route exactly the same as in my ...

Samba Shares don't show up in Windows 10 Network

Try using system-config-samba if running a Ubuntu based distro. All computers need to be so that the workgroup is named "WORKGROUP".