rebuilding a th350 and when installing the pump its tight and will not ...

TH350 transmission rebuild will not turn | NastyZ28.com

I do have the pump that takes the thrush washer with a tang. What I have done is assemble it with no clutches and test for end play and was .025 ...

rebuilding a th350 and when installing the pump its tight and will not go in all the way.. what could be causing this?

TH350 pump not going all the way in the case. - Yellow Bullet Forums

You may not have got the 2 halves aligned properly. Loosen all the pump half bolts, install the pump into the trans case upside down, tighten ...

Rebuilding my TH350. Any tips or tricks?? - ThirdGen.Org

Use Trans Gel for assembly lube. Vaseline will also work. Make sure it's clean. And I almost forgot to mention - the cleaner you can get ...

TH350 pump installation problems - The 1947 - 67-72 Chevy Trucks

While trying to go back together with it, the pump gets hung up. I believe its hanging up on the input shaft because when it gets stuck, the ...

How to Rebuild a TH350: Pump Assemblies - YouTube

In this video, I compare and contrast front pump assemblies from a TH350 and TH350C (TH350C takes a lock up converter) and go over ...

Rebuilt TH350, no go... - Chevy Tri Five Forum

If the oil pump was turning, the fluid level would have dropped at startup, and you'd have to add another 4-6 quarts of transmission fluid. What ...

Top 5 tips to know before rebuilding a TH350 Transmission pump

... its videos are not “directed to children” within. ... 90% of Toilets Are Installed Wrong (Here's the Right Way). Home RenoVision DIY•1.4M ...

TH350 assembly, what did I do wrong? - PY Online Forums

Too many shims under front bushing/bearing will eliminate endplay. Having the direct drum or forward drum hang up on the front pump will appear like there is no ...

No secrets here just a Th350 Rebuild - YouTube

He's gonna tear down his built TH350 transmission just for you. ... It is time for a 6L80 install! Express Auto & Transmission David Lee ...

TH350 Transmission Rebuild Part 2 - YouTube

... is just meant to show how I do it. Injury may occur by trying to replicate what is in this video. Attempt at your own risk, with proper ...

GM TH350 Transmission Disassembly Guide - CarTech Books

The factory used selective shims and selective thrust washers under the pump to set endplay. If a thrust washer kit is purchased, it usually comes with ...

T-350 rebuild - what happened to my endplay? - Hot Rod Forum

If these bushings are tight it may feel as if you have no endplay. DHMag brings up a good point about the pump washer/pump bearing issue however ...

no end play th350 | GM Square Body - 1973 - 1987 GM Truck Forum

HR is right, it will be very tight upon reassembly, the bushings inside the pump may need slight clearancing with wd-40 and fine sandpaper ...

GM TH350 Rebuild PT4 - Pump Assembly and Drum ... - YouTube

Part 4 of the TH350 rebuild series covers front pump assembly and clutch clearance checks for the forward and direct drum.

'71 TH350 Rebuild/Overhaul - ClassicOldsmobile.com

Get a overhaul kit with the Borg Warner or Raybestos high energy friction material (they are kinda greenish gray colored, the stick frictions ...

TH350 Rebuild Questions | GM Square Body - 1973

Just make sure you don't bottom out the bushing on the step inside the drum. If you do, you will either need remove it snd install another, or ...

Freshly rebuilt TH350 no gears any range on initial start-up

I poured as much fluid into the converter as it would take before installing it. ... I chose the Continental because it was suppose to be tight and operate ...

Rebuilt TH350 won't roll backwards - CorvetteForum

... pump back together and then it got a little tight. When I was ... it upright to ease the installation of the pump. With the first trans ...

TH350 Transmission Rebuild Part 1 - YouTube

Learn how to rebuild a high performance TH350 (commonly called a Turbo 350) automatic transmission. In this video I will show you how to ...