Effects of carbon nanotubes on open|hole carbon fiber reinforced ...

Interface engineering of carbon fiber composites using CNT: A review

Furthermore, it discusses the potential improvements in thermal and electrical conductivity achievable by incorporating CNTs at the interface, ...

Interlaminar fracture toughness properties of hybrid glass fiber ...

The electrospray deposition (ESD) method was used to deposit carbon nanotubes (CNTs) onto the surface of glass fiber (GF).

A review on carbon fiber-reinforced hierarchical composites

That being said, CFRP is met with difficulties such as delamination, weak interface, low damage resistance to impact, poor wettability and ...

densified Aligned Carbon Nanotubes Interlaminar Reinforcement

Vertically aligned carbon nanotubes (VACNTs) are placed between all plies in an aerospace carbon fiber reinforced ... Open hole compression specimen set-up. The ...

Study of Effect of Carbon nanotube on Tensile, Impact and Flexural ...

%, 1 wt.%, and 2 wt.% are added to the carbon fiber reinforcement polymer. The addition of CNT to CFRP resulted in improvement of tensile strength by 27.5 ...

Transformation of the released asbestos, carbon fibers and carbon ...

Carbon nanotubes (CNTs) with diameters below 100 nm exhibit properties including high strength and tensile stiffness, chirality-dependent ...

Simulating lightning effects on carbon fiber composite shielded with ...

Notably, the damage area in the CFRP protected with CNT sheets showed a substantial 78.1 % reduction compared to the unprotected CFRP sample. This suggests that ...

Experimental and Analytical Investigation of Flexural Behavior of ...

Carbon nanotubes (CNTs) are also attractive substances with a wide range of uses. A CNT may be thought of as a one-dimensional molecular cylinder. Due to their ...

NASA's Carbon Fiber-Carbon Nanotube Yarn Hybrid Reinforcement ...

Innovators at the NASA Glenn Research Center have developed a toughened hybrid reinforcement material made from carbon fiber and carbon ...

Carbon Nanotube Reinforced Strong Carbon Matrix Composites

The tensile strength was enhanced from 460 MPa for the pristine CNT fiber to 2.2 GPa for the CNT/C composite fiber after the PIP-w/RH process ...

Study on Mechanical Properties of Carbon Nanotube Reinforced ...

Compared with traditional materials, such as aluminum alloy and steel, carbon fiber reinforced resin matrix composites have the characteristics ...

Improvement of Interlaminar Fracture Properties of Out of Autoclave ...

Additionally, a small presence of carbon nanotubes is revealed in the fiber-matrix interface. Towards this direction, in the case of 0.5 wt% MWCNTs the ...

Out-of-autoclave molding of carbon fiber composites pipes with ...

A good adhesion among the plies was observed as well as the positive effects of CNTs deposition; an increase of 34%, 15% and 17% was obtained ...

Wet-spinning of carbon nanotube fibers: dispersion, processing and ...

The results corroborate the significance of CNTs aspect ratio and purity [37,38,60]. As a result, the mechanical properties of CNTFs assembled with a large ...

Effect of Multiwalled Carbon Nanotube on Compression Properties ...

The effectiveness of CNT addition on matrix dominated properties of composites has been evaluated by compression and open hole compression tests ...

Synergetic effects of carbon nanotube-graphene nanoplatelet ...

%, synergistically increase the mechanical performance and reduce the electrical percolation threshold of nanocomposites comparatively to the single filled ...

Potential Impact of Carbon Nanotube Reinforced Polymer (CNRP ...

This study investigates the possible use of carbon nanotubes as a molecular fiber in a composite material and illustrates the potential impact of ...

A review of the performance of fibre-reinforced composite laminates ...

This work defines the pros and cons of carbon nanotube (CNT)-based composites along with a systematic representation of the development of CNT-reinforced ...

Enhancement of out-of-plane mechanical properties of carbon fiber ...

To improve out-of-plane (transverse) mechanical properties, 0.5 and 1.0 Wt.% multi-walled carbon nanotubes (MWCNTs) were embedded into epoxy/CF composites.

Carbon nanotubes agglomeration in reinforced composites: A review

CNTs produce small clusters/agglomerates due to their high affinity and affect the texture of grain boundaries. This review discusses the effect ...