What size bolt do I need to remove a rear rotor?
2018 Rotor removal hole bolt size? - Toyota Tundra Forum
8mm head bolt I use short ones still pops them off. Click to expand... Will a 8 mm bolt work for both front and rear rotors.. I have a 2011 ...
Rear rotors replacement without removing control arm bolt possible?
You don't need to pull the arm that much. What I did was take a small prybar to pry the arm away maybe 1/4" to give enough room for bolt to back ...
Torx Bolt Size on Brake Rotor - My Ford Freestyle .com
It's a T40 on the FS, so I imagine it's the same on the T-Rex. That said, keep in mind it's just an assembly set screw, so if it gives you any trouble.
BOLT SIZE & TOOLS - TOYOTA ROTOR REMOVAL - JustAnswer
What size bolt is used to screw in to rotor to back off the rotoer ; Doing front hub assembly on 2008 Chevy Impala. Can you tell · ggrote1. Car ...
How do I get the rotors off? | Honda Element Owners Club
Ooops I forgot to mention...the bolts that help you to remove the rotors are 6mm x???. Usually any metric bolt from a Japaneese car that has a ...
What size bolt goes in the hole to back off the rotor? - Mazda 6 Forums
Thanks for your reply. Bolt in the back of the rotor? No. I will be changing my front rotors and may need bolt to 'force' the ...
Rear Rotor Removal | GMC Acadia Forum
Once you figure it out, get a bolt with a flat tip, not pointed, and screw it in the hole. This will push the rotor off of the drum. I had to ...
Brake Rotor (*%&$ screws won't come out!) - Honda Pilot Forums
Righty tighty lefty loosy. If you destroy them, just drill them out and forget about them, they are not needed, and they just thread into the ...
2013~2016: - Does anyone know the rotor bolt thread ... - Mazdas247
M8 X 1.25 bolt should be a standard size for those push-off hole on most rotors. For my 1998 Honda CR-V that bolt is on the parts list.
Seized brake rotor removal tool - Toyota GR86, 86, FR-S and ...
While replacing my wheel studs I discovered my rotors were stuck and I didn't have the correct size bolts on hand to remove them. I found ...
Removing rear rotors on 2500HD - Diesel Place
So what size Torx does it take to get the caliper bolts out? My calipers are mounted with large Torx bolts to "caliper carriers"? , which ...
"The screw" on Replacement Rotor | Honda Odyssey Forum
Any hardware store is fine: The bolts you need are 8 millimeters (8MM) by 1.25 millimeters (MM) thread pitch, hence the M8 comment above. Bolts ...
Rear rotors | Ford Explorer Forums
I am trying to change my rear rotors and pads on my 11 Explorer but cannot seem to get the right torx bolt size that holds the rotor.
Brake Rotor retaining bolt size?!?! - Land Rover Forums
... Need to remove the rotor from the hub housing. Thanks in advance ... does not need the clamping force of those screw's tensile strength.
How To Change Your Disc Brake Rotor Size | Maintenance Monday
You may wish to change the size of your brake rotors for a number of reasons. Maybe you're only riding on flat roads so don't need 160mm ...
2019 Mazda 3 rear brake caliper, what is the allen bolt size needed ...
Front caliper uses a 13mm and 17mm bolts, these are easier to access but still difficult to remove (my 2019 didn't have rust to speak of, but ...
Rear rotor bracket bolt issue - Kia Forum
If in fact you need to remove that bolt the arrow is pointing to, you could try a swivel socket or remove the bolt and nut across from it and ...
Rear Rotor removal | Dodge Caliber Forums
To remove the brake Caliber, you will need to remove the two 14mm bolts that mount it to the bracket. The upper bolt will be just the 14mm socket and the air ...
Rear Brake Rotor Replacement.......Good Luck ! | Kia Cadenza Forum
In order to take the rotor off, you have to remove the caliper bracket. One of the caliper bracket bolts runs right through the rear sway bar mount.
Fxr rear rotor bolts | V-Twin Forum
Bolts are suppose to be 3/8-16 X 1 Flat heads. weld a nut on top of the bolts that do not want to come out and use a socket to remove.