Should I replace the ball joints or the tie rods first?

Upper and lower ball joints and both outer tie rod ends - Facebook

Upper and lower ball joints and both outer tie rod ends! Bigger job than I expected wanting to just change the lower ball joints!!

New tires but now need ball joint and tie rod? - Infiniti FX Forum

You have to then buy a lower control arm and outer tie rod. The lower control arm ball joint is not serviceable and is part of the lower control ...

How many hours for Ball Joint/Tie Rod replacement?

About how long would it take to knock out both upper and lower ball joints, all the tie rod ends, and a track bar? Thanks in advance. 2006 CCSB ...

Replace 4 Ball Joints, 2 Tie Rods and 2 Stabilizer Links | GMTNation

Also, another tip I've picked up for removing tapered ball joints and tie rod ends, instead of pressing on the thread or shaft, use a hammer and ...

Does $700 seem too high for ball joint and tie rod ends replacement?

The tie rod ends is a pretty simple job, although if you're going to do all that, I would strongly recommend doing the ZJ upgrade. I'm not a ...

Tie Rods and Ball joints replacement - Bronco Forum

1) What else should I do at the same time? · 2)I have manual locking hubs, do I need to disassemble the hole hub in order to remove it and the ...

Questions about replacing the inner and outer tie rod ends on my 1st ...

Inner tie rods are the same thread pattern. Lefty loosey, righty tighty! Use a dab of red locktite on the threads upon installation and go get an alignment ...

Tie Rod Ends - Unofficial Honda FIT Forums

There is nothing wrong with getting new Tie Rod Ends if it you feel more at ease with them. Replacing just the boots will save some money as the ...

What else should I replace when I'm doing inner tie rods?

Even though it's a much harder job, I'm also tempted to replace the control arm ball joints and bushings. ... first. I thought I had the ...

Inner/Outer Tie Rod and Lower Ball Joint Replacement

This will walk through my experience replacing the inner and outer tie rods and lower ball joints. It was pretty easy thanks to no rust and PB ...

Are tie rods supposed to do this? | BobIsTheOilGuy - Bob is the Oil Guy

The inner tie rod joint is able to spin so it can back in or out of the outer tie rod for an alignment. E ...

Need to change tie rods, wheel bearings, hub assembly, but what ...

I would NOT replace your tie rods. I can't even imagine why they would need replacing unless taking damage from road debris. Maybe the bushings ...

Control Arm + Tie Rods, Order / Tips - Matthews Volvo Site

Likewise, if the tie rod is already removed then the knuckle may be on the floppy side when you go to remove the control arm ball joint from the ...

Tie rod end replacement | Nissan XTerra Forum

Moog parts today are nowhere near the quality they were in the 80's, 90's, or early 2000's. The Moog lower ball joints I installed were junk ...

outer tie rods; replacement question - Ranger-Forums

If you replace the tie rods you MUST get an alignment immediately afterwards, and the first thing he is going to do is put a wrench on the tie rod.

Tie rods and ball joints are shot! Anything better than stock to ...

Or has the subject of the thread now changed to "how can I upgrade my suspension with parts that will outlast or perform better than OE/stock ...

Tie Rod Ends, ball joints for 1989 240 - Turbobricks

When you unscrew the outer tie rod, count the number of rotations and then thread the new tie rod end on the same number of turns. This will get ...

Tierod replacement questions - Acura Enthusiast Community

I would opt not use aftermarket chassis parts like tie rods or ball joints. Or at least realize that its not safe. You'll need to check ...

Replacing inner tie rod, anything else? - NASIOC

if you look inside you will see a ball and socket at the rack end of the inner tie rod. You will notice that there is a metal washer with a tab ...

OEM vs Aftermarket: lower ball joint, outer tie rod, sway bar end links

If you need to loosen the sub frame or drop it a bit to get the sway bar bushings on, plus change the tie rod ends, you will need an alignment ...